Weed Eater Yogurt Maker GA2010 User Manual

R
Trademark  
Please do not return unit to retailer.  
Por favor, no devuelva el aparato al lugar de compra.  
Veuillez ne pas retourner l’outil au détaillant.  
1-800-554-6723  
Instruction Manual  
Manual de Instrucciones  
Manuel d’Instructions  
GA2010  
Gutter Cleanout Kit  
For Occasional Use Only  
WARNING:  
Read and follow all Safety Rules and Operating Instructions before  
using this product. Failure to do so can result in serious injury.  
ADVERTENCIA:  
Lea el manual de instrucciones y siga todas las advertencias e  
instrucciones de seguridad. El no hacerlo puede resultar en lesiones  
graves.  
AVERTISSEMENT:  
Lire le manuel d’instructions et bien respecter tous les avertisse-  
ments et toutes les instructions de sécurité. Tout défaut de le faire  
pourrait entraîner des blessures graves.  
Electrolux Home Products, Inc.  
250 Bobby Jones Expressway  
Augusta, GA 30907  
Copyright E2002 Electrolux Home Products, Inc.  
530088286  
2/7/02  
 
ASSEMBLY  
CARTON CONTENTS  
Check carton contents against the fol-  
lowing list. Refer to the illustrations in  
the OPERATION section of this manual.  
S Nozzle  
Electric  
Units  
with Tabs  
Tabs  
S Elbow with spacer ring  
S Extension Tube (4)  
S Pivot Tube  
S Adapter -- gas units with tabs  
S Adapter -- electric units with tabs  
S Adapter -- electric units with tube  
release button  
c Units  
h  
S Goggles  
elease  
ton  
Examine parts for damage. Do not use  
damaged parts.  
If you need assistance or find parts mis-  
sing or damaged, please call  
1-800-554-6723.  
Tube Release Button  
ASSEMBLY  
Match the blower outlet on your unit to  
one of those illustrated. To begin assem-  
bly, go to the section which corresponds  
to your blower outlet.  
GAS UNITS WITH TABS  
1. Stop engine and wait until impeller  
has completely stopped turning.  
2. Remove all tubes or other attach-  
ments from unit.  
3. Insert the notched end of the adapter  
into the elbow tube; push parts to-  
gether until the adapter snaps into  
place.  
Units  
Tabs  
Tabs  
Elbow  
Blower Outlet  
Notched End  
Groove  
Adapter  
4. Align the grooves on the adapter with  
the tabs inside the blower outlet.  
5. Insert the adapter into the blower out-  
let; turn adapter clockwise until parts  
snap into place.  
6. Proceed to ALL UNITS -- TUBE AS-  
SEMBLY.  
Electric  
its  
th  
GAS UNITS WITH SLOT &  
CLAMP RING  
ads  
1. Stop engine and wait until impeller  
has completely stopped turning.  
2. Remove all tubes or other attach-  
ments from unit.  
3. Thread spacer ring onto elbow threads  
until secure.  
-- 3 --  
 
4. Align the grooves on the adapter with  
the tabs on the blower outlet.  
5. Push adapter onto the blower outlet;  
turn adapter clockwise until parts  
snap into place.  
6. Proceed to ALL UNITS -- TUBE AS-  
SEMBLY.  
E
acer  
Ring  
ELECTRIC UNITS WITH TUBE  
RELEASE BUTTON  
Slot  
Key  
Clamp Ring  
1. Stop the motor, disconnect power  
source, and wait until impeller has  
completely stopped turning.  
4. Align key with slot and insert elbow  
into blower outlet.  
2. Remove all tubes or other attach-  
ments from unit.  
3. Insert the notched end of the adapter  
into elbow; push parts together until  
the adapter snaps into place.  
5. Securely tighten the clamp by turning  
the knob.  
6. Proceed to ALL UNITS -- TUBE AS-  
SEMBLY.  
ELECTRIC UNITS WITH THREADS  
1. Stop the motor, disconnect power  
source, and wait until impeller has  
completely stopped turning.  
2. Remove all tubes or other attach-  
ments from unit.  
Notched End  
Tube Release  
Hole for  
Button  
ube release  
utton  
3. Remove spacer ring from elbow.  
4. Thread the small end of the elbow  
into the blower outlet until the elbow  
stop is about 3/8 inch from blower  
outlet.  
Elbow  
Adapter  
t  
4. Align the grooves on the adapter with  
the grooves on the blower outlet.  
5. Push the adapter onto the blower out-  
let until it snaps into place (adapter is  
secured by tube release button).  
6. Proceed to ALL UNITS -- TUBE AS-  
SEMBLY.  
ALL UNITS -- TUBE ASSEMBLY  
1. Push the slotted end of the pivot tube  
over the elbow until the flange bottoms  
out in the elbow groove.  
5. Proceed to ALL UNITS -- TUBE AS-  
SEMBLY.  
ELECTRIC UNITS WITH TABS  
1. Stop the motor, disconnect power  
source, and wait until impeller has  
completely stopped turning.  
2. Remove all tubes or other attach-  
ments from unit.  
3. Insert the notched end of the adapter  
into the elbow tube; push parts to-  
gether until the adapter snaps into  
place.  
NOTE: Be sure flange snaps into groove.  
Pivot Tube  
Flange  
Elbow Groove  
Elbow  
2. Test rotating action of the pivot tube  
by rotating the pivot tube right and  
left.  
Notched  
End  
Groove  
Tab  
3. Assemble extension tubes up to a to-  
tal of 4, depending on the height of  
gutter to be cleaned.  
4. Thread nozzle onto the last tube.  
-- 4 --  
 
NOTE: Make sure threaded joints (tubes  
and nozzle) are securely tightened.  
5. Align the tube assembly in a vertical  
position.  
6. Thread extension tube assembly  
onto the end of the pivot tube.  
Pivot  
Tube  
Nozzle  
Extension  
Tubes  
Elbow  
OPERATION  
KNOW YOUR GUTTER ATTACHMENT  
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR  
UNIT. Compare illustrations to your unit to familiarize yourself with the location of  
the various controls and adjustments. Save this manual for future reference.  
Adapter for  
Gas Units with  
Mounting Tabs  
Adapter for  
Adapter for  
Electric Units  
Electric Units  
with Tube  
Nozzle  
with Mounting Tabs  
Release Button  
Extension Tube  
Pivot Tube  
Decal  
Elbow with Spacer Ring  
Goggles  
STARTING INSTRUCTIONS  
STARTING  
POSITION  
(for gas units only)  
WARNING: You MUST make sure  
the tubes are secure before using the unit.  
Do not use the unit without all of the tubes  
properly attached to avoid flying debris  
and/or impeller contact which can cause  
serious injury. Always wear eye protection  
to prevent rocks or debris from being  
blown or ricocheting into the eyes and  
face which can result in blindness or seri-  
ous injury.  
D Follow the STARTING INSTRUCTIONS  
in your instruction manual.  
D Support the gutter attachment with  
one hand as soon as the engine or  
motor starts.  
WARNING: Hold the unit as illus-  
trated when starting (for gas units only).  
Do not set unit on any surface except a  
clean, hard area when starting and/or  
using the unit. Debris such as gravel,  
sand, dust, grass, etc could be picked  
up by the air intake and thrown out  
through the discharge opening, damag-  
ing the unit or property, or causing seri-  
ous injury to bystanders or the operator.  
SUPPORT  
THE TUBES  
NOTE: When starting unit, lean the top of OPERATING TIPS  
gutter attachment against a wall, tree, etc.,  
for support.  
D
Wear eye protection to guard against  
eye injury.  
-- 5 --  
 
D To reduce the risk of hearing loss as-  
sociated with sound level(s), hearing  
protection is required.  
D To reduce the risk of injury associated  
with contacting rotating parts, stop the  
engine/disconnect from the power  
source and wait until impeller has  
completely stopped turning before  
installing or removing attachments.  
D Stand 3 to 4 feet away from building.  
D Rotate the pivot tube to position the  
nozzle right or left.  
MAINTENANCE  
CHECK FOR CLOGGED TUBES  
S Nozzle and tubes should be free from  
obstructions and debris.  
AFTER EACH USE  
BEFORE EACH USE  
CHECK FOR LOOSE  
FASTENERS AND PARTS  
S Nozzle and tube connections  
S Adapter (if used)  
INSPECT AND CLEAN UNIT AND LA-  
S Screws and handles on blower  
BELS  
CHECK FOR DAMAGED OR  
WORN PARTS  
Contact an authorized service dealer for  
S Inspect complete unit for loose or  
damaged parts. Clean the unit using a  
damp cloth with a mild detergent.  
replacement of damaged or worn parts. S Wipe off unit with a clean dry cloth.  
STORAGE  
SEASONAL STORAGE  
WARNING: Perform the followIng  
steps after each use:  
Prepare your unit for storage at the end  
of the season or if it will not be used for  
30 days or more.  
S Allow motor/engine to cool before  
storing or transporting.  
If your unit is to be stored for a period of  
time:  
S Store the unit well out of the reach of  
children.  
S Clean the unit thoroughly before  
lengthy storage.  
S Store in a clean dry area.  
-- 6 --  
 

Welbilt Bread Maker ABM 1OO 4 User Manual
Western Digital Portable Multimedia Player WDBABX0000NBK NESN User Manual
Whirlpool Dishwasher DP8700XT Series User Manual
Whirlpool Water Heater T K1S User Manual
Wizcom Scanner 2 Professional User Manual
Woodstock Grinder M1051 User Manual
Xerox Printer Accessories 6128MFP User Manual
Yamaha Cassette Player KX 380 User Manual
ZALMAN Fan CNPS7000A User Manual
Zanussi Ice Maker 730523 User Manual