Westinghouse Indoor Furnishings 70286 User Manual

Item #  
70285, 70286  
Mini-Pendant Kit  
Installation and Safety Instructions  
Warning: Be sure the electricity to the wires you are working on is shut off; either the fuse is removed  
or the circuit breaker is shut off.  
General  
You don't need special tools to install this fixture. Be sure to follow the steps in the order given. Under no  
circumstances should a fixture be hung on house electrical wires, nor should a swag type fixture be installed on  
a ceiling which contains a radiant type heating system. Read instructions carefully. If you are unclear as to  
how to proceed, consult a qualified electrician.  
A
C
B
InStallatIon  
Important: Do not attach fixture directly to outlet box.  
Step 1: Thread mounting screw (A) into the matching hole of mounting bar (B).  
Step 2: Secure the mounting bar (B) to outlet box with outlet box screws (C) (not provided).  
D
E
GroundInG InStructIonS  
Step 1: Insert the green grounding screw into the hole with two raised dimples on the mounting bar.  
Wrap the ground wire (green wire with tracer and green label) from the fixture (if supplied) around  
the green grounding screw, then connect it to ground wire (green wire with tracer and green label)  
from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied). Never  
connect ground wire to black or white power supply wires.  
Step 2: Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into  
and connect the wires according to the directions below.  
Group a: Connect to black house wire: transparent, brownish grey or brown with  
tracer (with black label)  
Group B: Connect to white house wire: transparent or without tracer (with white label)  
*Note: When parallel wire (SVT) is used, the tracer wire is connected to group A and the wire without  
a tracer is connected to group B (seen best when viewed from wire end).  
Step 3: Take your fixture wire(s) from group A and place evenly against the black wire from the outlet box.  
Do NOT twist wires together before using wire connectors.  
Step 4: Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.  
Step 5: Try to gently pull the connectors off the wires. If you can pull the connector off, carefully repeat  
steps 3 and 4 above, and check again for a firm connection.  
Step 6: Connect the fixture wire from group B to the white wire from the outlet box in the same manner.  
Make sure no bare wires can be seen outside wire connectors.  
FInal aSSeMBly  
Step 1: After wires are connected, tuck them carefully inside outlet box. Raise canopy (D) allowing the  
mounting screw (A) to protrude through the hole in the canopy (D), and secure with ball nut (E).  
Step 2: Install the glass onto the socket (F) and secure the retaining ring (G).  
Step 3: Install lamp. (Please do not exceed the maximum capacity recommended on the socket).  
F
G
cleanInG  
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as  
scouring pads or powders, steel wool or abrasive paper.  
Westinghouse Lighting Corporation, Philadelphia, PA 19154-1029, U.S.A.  
Westinghou g Corporation, a Westinghouse Electric Corporation licensee  
and “Westinghouse” are registered trademarks of Westinghouse Electric Corporation  
y “Westinghouse”estan marca registrada por Westinghouse Electric Corporation  
et “Westinghouse” sont des marques déposéesde Westinghouse Electric Corporation  
Made in China / Hecho en China / Fabriqué en Chine  
© 2013 WESTINGHOUSE LIGHTING CORP.  
 

Weider Home Gym 831150301 User Manual
Weider Home Gym WEBE08900 User Manual
Westinghouse Outdoor Ceiling Fan WH14 User Manual
Whirlpool Microwave Oven YKHMS175M User Manual
Williams Sound Stereo Receiver WIR SYS 90 PRO User Manual
Woodstock Grinder W1681 User Manual
Yamaha Jet Ski F1W F8199 10 User Manual
Yamaha Speaker DM 2000VCM User Manual
Yamaha Speaker System AS312 User Manual
Zanussi Ventilation Hood 641257 User Manual