Whirlpool Range 9754384 User Manual

®
ELECTRIC RANGE  
Use & Care Guide  
For questions about features, operation/performance  
parts, accessories or service, call: 1-800-253-1301.  
or visit our website at...  
Table of Contents................................................. 2  
9756384  
 
RANGE SAFETY  
Your safety and the safety of others are very important.  
We have provided many important safety messages in this manual and on your appliance. Always read and obey all  
safety messages.  
This is the safety alert symbol.  
This symbol alerts you to potential hazards that can kill or hurt you and others.  
All safety messages will follow the safety alert symbol and either the word “DANGER” or  
“WARNING.” These words mean:  
You can be killed or seriously injured if you don't  
immediately follow instructions.  
You can be killed or seriously injured if you don't  
follow instructions.  
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you  
what can happen if the instructions are not followed.  
The Anti-Tip Bracket  
The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door without the  
anti-tip bracket fastened down properly.  
WARNING  
Tip Over Hazard  
A child or adult can tip the range and be killed.  
Connect anti-tip bracket to rear range foot.  
Reconnect the anti-tip bracket, if the range is moved.  
See the installation instructions for details.  
Failure to follow these instructions can result in death or serious burns to children  
and adults.  
Anti-Tip Bracket  
Making sure the anti-tip bracket is installed:  
Slide range forward.  
Look for the anti-tip bracket securely attached to floor.  
Slide range back so rear range foot is under anti-tip bracket.  
Range Foot  
The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list  
of substances known to the State of California to cause cancer, birth defects, or other reproductive harm, and  
requires businesses to warn of potential exposure to such substances.  
WARNING: This product contains a chemical known to the State of California to cause cancer, birth defects, or  
other reproductive harm.  
This appliance can cause low-level exposure to some of the substances listed, including benzene, formaldehyde,  
carbon monoxide, and toluene.  
3
 
IMPORTANT SAFETY INSTRUCTIONS  
WARNING: To reduce the risk of fire, electrical  
I Use Proper Pan Size The range is equipped with  
one or more surface units of different size. Select  
utensils having flat bottoms large enough to cover  
the surface unit heating element. The use of under-  
sized utensils will expose a portion of the heating  
element to direct contact and may result in ignition  
of clothing. Proper relationship of utensil to burner  
will also improve efficiency.  
shock, injury to persons, or damage when using the  
range, follow basic precautions, including the  
following:  
I
WARNING: TO REDUCE THE RISK OF  
TIPPING OF THE RANGE, THE RANGE MUST BE  
SECURED BY PROPERLY INSTALLED ANTI-TIP  
DEVICES. TO CHECK IF THE DEVICES ARE  
INSTALLED PROPERLY, SLIDE RANGE FORWARD,  
LOOK FOR ANTI-TIP BRACKET SECURELY  
ATTACHED TO FLOOR, AND SLIDE RANGE BACK  
SO REAR RANGE FOOT IS UNDER ANTI-TIP  
BRACKET.  
I Never Leave Surface Units Unattended at High Heat  
Settings Boilover causes smoking and greasy  
spillovers that may ignite.  
I Make Sure Reflector Pans or Drip Bowls Are in  
Place Absence of these pans or bowls during  
cooking may subject wiring or components under-  
neath to damage.  
I
CAUTION: Do not store items of interest to  
children in cabinets above a range or on the back-  
guard of a range children climbing on the range to  
reach items could be seriously injured.  
I Protective Liners Do not use aluminum foil to line  
surface unit drip bowls or oven bottoms, except as  
suggested in the manual. Improper installation of  
these liners may result in a risk of electric shock, or  
fire.  
I Proper Installation Be sure the range is properly  
installed and grounded by a qualified technician.  
I Never Use the Range for Warming or Heating the  
Room.  
I Glazed Cooking Utensils Only certain types of  
glass, glass/ceramic, ceramic, earthenware, or other  
glazed utensils are suitable for range-top service  
without breaking due to the sudden change in  
temperature.  
I Do Not Leave Children Alone Children should not  
be left alone or unattended in area where the range  
is in use. They should never be allowed to sit or  
stand on any part of the range.  
I Utensil Handles Should Be Turned Inward and Not  
Extend Over Adjacent Surface Units To reduce the  
risk of burns, ignition of flammable materials, and  
spillage due to unintentional contact with the utensil,  
the handle of a utensil should be positioned so that  
it is turned inward, and does not extend over  
adjacent surface units.  
I Wear Proper Apparel Loose-fitting or hanging  
garments should never be worn while using the  
range.  
I User Servicing Do not repair or replace any part of  
the range unless specifically recommended in the  
manual. All other servicing should be referred to a  
qualified technician.  
I Do Not Soak Removable Heating Elements –  
Heating elements should never be immersed in  
water.  
I Storage in or on the Range Flammable materials  
should not be stored in an oven or near surface  
units.  
I Do Not Cook on Broken Cooktop If cooktop  
should break, cleaning solutions and spillovers may  
penetrate the broken cooktop and create a risk of  
electric shock. Contact a qualified technician  
immediately.  
I Do Not Use Water on Grease Fires Smother fire or  
flame or use dry chemical or foam-type extinguisher.  
I Use Only Dry Potholders Moist or damp  
potholders on hot surfaces may result in burns from  
steam. Do not let potholder touch hot heating  
elements. Do not use a towel or other bulky cloth.  
I Clean Cooktop With Caution If a wet sponge or  
cloth is used to wipe spills on a hot cooking area,  
be careful to avoid steam burn. Some cleaners can  
produce noxious fumes if applied to a hot surface.  
I DO NOT TOUCH SURFACE UNITS OR AREAS  
NEAR UNITS Surface units may be hot even  
though they are dark in color. Areas near surface  
units may become hot enough to cause burns.  
During and after use, do not touch, or let clothing or  
other flammable materials contact surface units or  
areas near units until they have had sufficient time  
to cool. Among those areas are the cooktop and  
surfaces facing the cooktop.  
I Use Care When Opening Door Let hot air or  
steam escape before removing or replacing food.  
I Do Not Heat Unopened Food Containers Build-up  
of pressure may cause container to burst and result  
in injury.  
SAVE THESE INSTRUCTIONS  
4
 
IMPORTANT SAFETY INSTRUCTIONS  
For self-cleaning ranges –  
I Keep Oven Vent Ducts Unobstructed.  
I Do Not Clean Door Gasket The door gasket is  
essential for a good seal. Care should be taken not  
to rub, damage, or move the gasket.  
I Placement of Oven Racks Always place oven  
racks in desired location while oven is cool. If rack  
must be moved while oven is hot, do not let  
potholder contact hot heating element in oven.  
I Do Not Use Oven Cleaners No commercial oven  
cleaner or oven liner protective coating of any kind  
should be used in or around any part of the oven.  
I DO NOT TOUCH HEATING ELEMENTS OR  
INTERIOR SURFACES OF OVEN Heating  
elements may be hot even though they are dark in  
color. Interior surfaces of an oven become hot  
enough to cause burns. During and after use, do  
not touch, or let clothing or other flammable  
materials contact heating elements or interior  
surfaces of oven until they have had sufficient time  
to cool. Other surfaces of the appliance may  
become hot enough to cause burns among these  
surfaces are oven vent openings and surfaces near  
these openings, oven doors, and windows of oven  
doors.  
I Clean Only Parts Listed in Manual.  
I Before Self-Cleaning the Oven Remove broiler pan  
and other utensils.  
For units with ventilating hood –  
I Clean Ventilating Hoods Frequently Grease should  
not be allowed to accumulate on hood or filter.  
I When flaming foods under the hood, turn the fan on.  
SAVE THESE INSTRUCTIONS  
5
 
PARTS AND FEATURES  
This manual covers several different models. The range you have purchased may have some or all of the parts and features listed. The  
location and appearance of the features shown here may not match your model.  
Control Panel  
6
3
7
2
4
5
1
8
10  
9
1. ACCUSIMMER® Range Indicator Light  
(on some models)  
2. Left Front Control Knob  
(ACCUSIMMER® Range Control Knob  
on some models)  
4. Left Rear Control Knob  
5. Electronic Oven Control  
6. Right Rear Control Knob  
7. Right Front Control Knob  
8. ACCUSIMMER® Range Switch (on some models)  
9. Surface Cooking Area Locator  
10. Keep Warm Element Control Knob  
(on some models)  
3. Surface Heating Indicator Light  
Range  
7
8
1
2
3
9
10  
13  
11  
12  
4
5
6
1. Oven Vent (on ceramic glass  
models)  
2. Ceramic Glass (on some  
models)  
3. Dual Element  
(on some models)  
6. Storage Drawer (on some  
models) or Warming Drawer (on  
some models)  
7. Control Panel  
8. Keep Warm Element  
(on some models)  
10. Automatic Oven Light Switch  
11. Broil Element (not shown)  
12. Bake Element  
Parts and Features Not Shown  
Coil Elements (on some models)  
Oven Door Window  
Oven Light  
Broiler Pan and Grid  
Roasting Rack  
13. Self-Clean Latch  
4. Anti-Tip Bracket  
9. Hot Surface Indicator Light (on  
ceramic glass models)  
Storage Drawer Liner  
(on some models)  
5. Model and Serial Number Plate  
(behind left side of storage  
drawer)  
6
 
ACCUSIMMER® Feature  
COOKTOP USE  
(on some models)  
The ACCUSIMMER® feature setting is an adjustable heat setting  
for more precise simmering. It is the left front surface cooking  
area or element. The indicator light will glow when the  
ACCUSIMMER® feature is in use.  
Cooktop Controls  
WARNING  
(NOTE: Picture may vary depending on your model)  
The ACCUSIMMER® control knob has two settings: SIMMER and  
NORMAL BURNER. When the control is set on NORMAL  
BURNER, the left front surface cooking area or element will  
function as a single or dual element (on some models).  
Fire Hazard  
Turn off all controls when done cooking.  
Failure to do so can result in death or fire.  
To use:  
1. Turn the ACCUSIMMER® Range control knob to the SIMMER  
position. The indicator light will glow.  
The control knobs can be set anywhere between HI and LO. Push  
in and turn to setting. Use the following chart as a guide when  
setting heat levels.  
2. Push in and turn the left front control knob to a setting  
between LO and 5.  
Select LO for a low simmer or when using lids and 5 for a high  
simmer or when not using lids.  
SETTING  
HI  
RECOMMENDED USE  
On some models, select either the Single or Dual Zone  
settings. See Dual Cooking Zone” section.  
3. Turn the ACCUSIMMER® Range control knob back to the  
Normal Burner setting when finished cooking. The indicator  
light will go out.  
I
I
Start food cooking.  
Bring liquid to a boil.  
I
I
Hold a rapid boil.  
6-8  
[MED- HI]  
Quickly brown or sear food.  
5
I
I
I
Maintain a slow boil.  
Dual Cooking Zone  
[MED]  
Fry or sauté foods.  
Cook soups, sauces and gravies.  
(on some models)  
2-4  
[MED- LO]  
I
I
Stew or steam food.  
Simmer.  
1
2
LO  
I
I
Keep food warm.  
Melt chocolate or butter.  
ACCUSIMMER®  
(on some models)  
I
Precise simmer control.  
I
I
Low simmer or when using lids.  
4
LO  
1. Single size (6 in. [15.24 cm])  
2. Dual size (10 in. [25.4 cm])  
High simmer or simmer without lids.  
Keep Warm Element  
(on some ceramic  
glass models)  
I
Keep cooked foods warm.  
The Dual Cooking Zone offers flexibility depending on the size of  
the cookware. Single size can be used in the same way as a  
regular element. The dual size combines both the single and  
outer element and is recommended for larger size cookware.  
SINGLE  
DUAL  
OFF  
LO  
LO  
2
2
REMEMBER: When range is in use or (on some  
models) during the Self-Cleaning cycle, the entire  
cooktop area may become hot.  
4
4
6
6
8
8
HI  
I H  
1. Single  
2. Dual  
7
 
To Use SINGLE:  
1. Push in and turn the left front control knob counterclockwise  
from the OFF position to the SINGLE zone anywhere between  
HI and LO.  
Ceramic Glass  
(on some models)  
2. Push in and turn knob to OFF when finished.  
The surface cooking area will glow red when an element is on. It  
will cycle on and off, at all settings, to maintain the selected heat  
level.  
To Use DUAL:  
1. Push in and turn the left front control knob clockwise from the  
It is normal for the surface of white ceramic glass to appear to  
change color when surface cooking areas are hot. As the glass  
cools, it will return to its original color.  
OFF position to the DUAL zone anywhere between HI and  
LO.  
2. Push in and turn knob to OFF when finished.  
Wiping off the cooktop before and after each use will help keep it  
free from stains and provide the most even heating. For more  
information, see General Cleaningsection.  
Keep Warm Element  
I
Do not store jars or cans above the cooktop. Dropping a  
heavy or hard object onto the cooktop could crack it.  
(on some models)  
I
Do not leave a hot lid on the cooktop. As the cooktop cools,  
air can become trapped between the lid and the cooktop,  
and the ceramic glass could break when the lid is removed.  
WARNING  
I
I
Clean up sugary spills and soils as soon as hot surface  
indicator light goes off. If spills or soils are not wiped up while  
warm, surface pitting can occur.  
Food Poisoning Hazard  
Do not let food sit for more than one hour before  
or after cooking.  
Do not slide cookware or bakeware across the cooktop.  
Aluminum or copper bottoms and rough finishes on  
cookware or bakeware could leave scratches or marks on the  
cooktop.  
Doing so can result in food poisoning or  
sickness.  
I
I
Do not cook popcorn in prepackaged aluminum containers  
on the cooktop. It could leave aluminum marks that cannot  
be removed completely.  
Use the Keep Warm Element to keep cooked foods warm. One  
hour is the recommended maximum time to maintain food  
quality.  
Do not allow objects that could melt, such as plastic or  
aluminum foil, to touch any part of the entire cooktop.  
Do not use it to heat cold foods.  
The Keep Warm Element can be used alone or when any of the  
other surface cooking areas are being used, and can be set from  
MIN to MAX for different levels of heating.  
I
I
Do not use the cooktop as a cutting board.  
Use cookware about the same size as the surface cooking  
area. Cookware should not extend more than 1 in. (2.5 cm)  
outside the area.  
The Keep Warm Element area will not glow red when cycling on.  
However, its indicator light will glow as long as the Keep Warm  
Element area is too hot to touch.  
I
Use only cookware and dishes recommended for oven and  
cooktop use.  
I
Cover all foods with a lid or aluminum foil. When warming  
baked goods, allow a small opening in the cover for moisture  
to escape.  
I
I
Do not use plastic wrap to cover food. Plastic wrap may melt.  
Use pot holders or oven mitts to remove food.  
KEEP WARM  
1. Surface Cooking Area  
2. Cookware/Canner  
3. 1 in. (2.5 cm) Maximum Overhang  
OFF MAX  
MIN  
I
I
Use flat-bottomed cookware for best heat conduction and  
energy efficiency. Cookware with rounded, warped, ribbed or  
dented bottoms could cause uneven heating and poor  
cooking results.  
Determine flatness by placing the straight edge of a ruler  
across the bottom of the cookware. While rotating the ruler,  
no space or light should be visible between it and the  
cookware.  
To Use:  
I
I
Cookware designed with slightly indented bottoms or small  
expansion channels can be used.  
1. Push in and turn KEEP WARM knob to desired setting.  
2. Turn knob to OFF when finished.  
Make sure the bottoms of pots and pans are clean and dry  
before using them. Residue and water can leave deposits  
when heated.  
I
Do not cook foods directly on the cooktop.  
8
 
Hot Surface Indicator Light (under ceramic glass)  
The hot surface indicator light will glow as long as any surface  
cooking area is too hot to touch, even after the surface cooking  
area(s) is turned off.  
Lift-up Cooktop  
(on some models)  
The lift-up cooktop provides easy access for cleaning beneath.  
Do not drop the cooktop. Damage could occur to the finish and  
the cooktop frame. For more information, see the General  
Cleaningsection.  
HOT SURFACE  
To Lift:  
Lift the cooktop by both front corners until the supports lock into  
place.  
Coil Elements and Burner Bowls  
(on some models)  
Coil elements should be level for optimal cooking results. Burner  
bowls, when clean, reflect heat back to the cookware. They also  
help catch spills.  
Cookware should not extend more than 1 in. (2.5 cm) over the  
coil element. If cookware is uneven or too large, it can produce  
excess heat causing the burner bowl to change color. For more  
information, see the General Cleaningsection.  
To Replace:  
Before removing or replacing coil elements and burner bowls,  
make sure they are cool and the control knobs are in the off  
position.  
1. Lift the cooktop from both sides while pressing the support  
rods back to unlock them.  
2. Slowly lower the cooktop into place.  
To Remove:  
1. Push in the edge of coil element toward the receptacle. Then  
lift it just enough to clear the burner bowl.  
Home Canning  
When canning for long periods, alternate the use of surface  
cooking areas, elements or surface burners between batches.  
This allows time for the most recently used areas to cool.  
I
Center the canner on the grate or largest surface cooking  
area or element. Canners should not extend more than 1 in.  
(2.5 cm) outside the cooking area.  
I
Do not place canner on two surface cooking areas, elements  
or surface burners at the same time.  
2. Pull the coil element straight away from the receptacle.  
I
I
On ceramic glass models, use only flat-bottomed canners.  
On coil element models, the installation of a Canning Unit Kit  
is recommended. If a kit is not installed, the life of the coil  
element will be shortened. See Assistance or Servicefor  
ordering instructions.  
I
For more information, contact your local U.S. Government  
Agricultural Department Extension Office. In Canada, contact  
Agriculture Canada. Companies that manufacture home  
canning products can also offer assistance.  
3. Lift out the burner bowl.  
To Replace:  
1. Line up openings in the burner bowl with the coil element  
Cookware  
receptacle.  
IMPORTANT: Never leave empty cookware on a hot surface  
cooking area, element or surface burner.  
Ideal cookware should have a flat bottom, straight sides, a well-  
fitting lid and the material should be of medium-to-heavy  
thickness.  
Rough finishes may scratch the cooktop. Aluminum and copper  
may be used as a core or base in cookware. However, when used  
as a base they can leave permanent marks on the cooktop or  
grates.  
2. Holding the coil element as level as possible, carefully push  
coil element terminal into the receptacle.  
Cookware material is a factor in how quickly and evenly heat is  
transferred, which affects cooking results. A nonstick finish has  
the same characteristics as its base material. For example,  
aluminum cookware with a nonstick finish will take on the  
properties of aluminum.  
3. When the terminal is pushed into the receptacle as far as it  
will go, push down the edge of the coil element opposite the  
receptacle.  
9
 
Use the following chart as a guide for cookware material  
characteristics.  
Style 2 Electronic Oven Controls (on some models)  
2 4 5  
1
3
6
COOKWARE  
Aluminum  
CHARACTERISTICS  
I
I
I
Heats quickly and evenly.  
Suitable for all types of cooking.  
Medium or heavy thickness is best for  
most cooking tasks.  
Cast iron  
I
I
I
Heats slowly and evenly.  
Good for browning and frying.  
Maintains heat for slow cooking.  
Ceramic or  
Ceramic glass  
I
I
I
Follow manufacturers instructions.  
Heats slowly, but unevenly.  
11  
10  
9
8
7
Ideal results on low to medium heat  
settings.  
1. Oven Display  
2. Clock  
3. Timer/Cancel  
7. Temperature/Time  
8. Cook Time  
9. Start Time  
Heats very quickly and evenly.  
Copper  
I
4. Start/Enter  
(Control Lock)  
5. Auto Clean  
6. Off/Cancel  
10. Custom Broil  
11. Bake  
I
I
Follow manufacturers instructions.  
Earthenware  
Use on low heat settings.  
I
See stainless steel or cast iron.  
Porcelain enamel-  
on-steel or cast  
iron  
Display  
Stainless steel  
I
I
Heats quickly, but unevenly.  
When power is first supplied to the appliance, PFwill appear on  
the display. Press CANCEL or OFF/CANCEL to clear PFfrom  
the display.  
A core or base of aluminum or copper on  
stainless steel provides even heating.  
If PFappears at any other time, a power failure has occurred.  
Press CANCEL or OFF/CANCEL and reset the Clock if needed.  
ELECTRONIC OVEN  
CONTROLS  
When the oven is not in use, the display shows the time of day.  
When performing a timed cook function, the display will show  
either hours and minutes, or minutes and seconds.  
Style 1 Electronic Oven Controls (on some models)  
Start  
The START or START/ENTER pad begins any oven function. If not  
pressed within 5 seconds after pressing a function pad, the  
START?indicator light will flash as a reminder. On some  
models, START?will appear on the display.  
If not pressed within 5 minutes after pressing a function pad, the  
oven display will return to the time of day mode and the  
programmed function will be canceled.  
Cancel or Off/Cancel  
The CANCEL or OFF/CANCEL pad stops any function except the  
Clock, Timer and Control Lock.  
1. Display  
2. Timer  
3. Clock  
4. Auto Clean  
5. Oven Light Pad (on some  
models)  
6. Sequence Programming  
(on some models)  
7. Oven Settings  
8. Warming Drawer  
(on some models)  
9. Temperature  
10. Timed Cooking  
(on some models)  
11. Hour/Minute  
(on some models)  
Clock  
On some models, this is a 12-hour clock that shows a.m. and  
p.m.  
12. Start/Control Lock  
13. Off/Cancel  
To Set:  
Before setting, make sure the oven and Timer are off.  
1. Press CLOCK.  
2. Depending on your model, press the HR or MIN or TIME/  
TEMP upor downarrow pads to set the time of day. Only  
on some models can the time be set to include a.m. or p.m.  
3. Press CLOCK or START.  
10  
 
To display the time of day for 5 seconds when the timer is  
counting down, press CLOCK.  
Tones  
Tones are audible signals, indicating the following:  
Control Lock  
One tone  
The Control Lock shuts down the control panel pads to prevent  
unintended use of the oven.  
I
I
I
I
Valid pad press  
When the control is locked, only the ACCUSIMMER, CLOCK SET,  
OVEN LIGHT (on some models) and TIMER pads will function.  
Oven is preheated (long tone)  
Function has been entered  
To Lock/Unlock Control: Before locking, make sure the oven  
and Timer are off. Press and hold START for 5 seconds. A single  
tone will sound, and Locwill appear on the display.  
Reminder (on some models), repeating each minute after the  
end-of-cycle tones  
Repeat to unlock. Locwill disappear from the display.  
Three tones  
I
Invalid pad press  
Oven Temperature Control  
Four tones  
IMPORTANT: Do not use a thermometer to measure oven  
temperature because opening the oven door may cause burner  
cycling to give incorrect readings.  
I
End of cycle  
Reminder Tones (on some models): Reminder tones may be  
turned off. Press and hold STOP TIME for 5 seconds. rEP OFF”  
or offwill appear in the display. Repeat to turn reminder tones  
back on, and rEP onor onwill appear in the display.  
The oven provides accurate temperatures; however, it may cook  
faster or slower than your previous oven, so the temperature  
calibration can be adjusted. It can be changed in Fahrenheit or  
Celsius.  
All Tones: All of the above tones are preset on. All except the  
end-of-cycle tones can be turned off.  
A minus sign means the oven will be cooler by the displayed  
amount. No sign means the oven will be warmer by the displayed  
amount. Use the following chart as a guide.  
To Turn Off/On (on some models): Press and hold START TIME  
for 5 seconds. A tone will sound and Snd OFFwill appear on  
the display. Repeat to turn tones on, and Snd onwill appear on  
the display.  
ADJUSTMENT °F  
(ADJUSTMENT °C)  
COOKS FOOD  
On some models, only the loudness of the tones can be adjusted.  
On other models, the tones cannot be adjusted or turned off.  
10°F (5°C)  
...a little more  
...moderately more  
...much more  
Tone Pitch: The pitch is preset at high, but can be changed to  
low. On some models, only the loudness of the tones can be  
adjusted. On other models, the tones cannot be adjusted or  
turned off.  
20°F (10°C)  
30°F (15°C)  
-10°F (-5°C)  
-20°F (-10°C)  
-30°F (-15°C)  
To Change (on some models): Press and hold BAKE for 5  
seconds. A tone will sound, and Snd LOwill appear on the  
display. Repeat to change, and Snd Hiwill appear on display.  
...a little less  
...moderately less  
...much less  
Fahrenheit and Celsius  
The temperature is preset at Fahrenheit, but can be changed to  
Celsius on some models.  
To Adjust Oven Temperature Calibration:  
1. Press and hold BAKE for 5 seconds until the oven display  
shows the current calibration, for example 0°F CALor 00.”  
To Change: Press and hold CUSTOM BROIL for 5 seconds. A  
tone will sound, and “°Cwill appear on the display. Repeat to  
change back to Fahrenheit. To exit mode, press CANCEL.  
2. Press the TEMP or TEMP/TIME upor downarrow pad(s)  
to increase or to decrease the temperature in 10°F (5°C)  
amounts. The adjustment can be set between 30°F (15°C)  
and -30°F (-15°C).  
Timer  
The Timer can be set in hours or minutes up to 12 hours and 59  
minutes, and counts down the set time. The Timer does not start  
or stop the oven.  
3. Press START.  
OVEN USE  
To Set:  
1. Press TIMER SET or TIMER CANCEL*. The timer indicator  
light will light up on some models. If no action is taken after 5  
minutes, the display will return to the time of day mode.  
Odors and smoke are normal when the oven is used the first few  
times, or when it is heavily soiled.  
IMPORTANT: The health of some birds is extremely sensitive to  
the fumes given off. Exposure to the fumes may result in death to  
certain birds. Always move birds to another closed and well  
ventilated room.  
2. Depending on your model, press the HR or MIN or TIME/  
TEMP upor downarrow pads to set the length of time to  
cook.  
3. Press START or TIMER SET. When the set time ends, end-of-  
cycle tones will sound, then, if enabled, reminder tones will  
sound every minute on some models.  
4. Press TIMER OFF or TIMER CANCEL* anytime to cancel the  
Timer and reminder tones.  
Remember, do not press the CANCEL pad because the oven  
will turn off.  
11  
 
Aluminum Foil  
Split Oven Rack  
IMPORTANT: Do not line the oven bottom with any type of foil,  
liners or cookware because permanent damage will occur to the  
oven bottom finish.  
(on some models)  
Split-Rack with Removable Insert  
I
Do not cover entire rack with foil because air must be able to  
move freely for best cooking results.  
The split-rack with removable insert is a space maximizer. When  
the two are attached, they make a full rack. The insert can also be  
removed to provide room for large items such as a turkey and  
casseroles.  
I
To catch spills, place foil on rack below dish. Make sure foil is  
at least 1 in. (2.5 cm) larger than the dish and that it is turned  
up at the edges.  
The insert can also be used on the counter for a cooling rack.  
Do not place more than 25 lbs. (11.3 kg) on the split-rack.  
I
Do not cover food with aluminum foil when convection  
cooking (on some models).  
2
Positioning Racks and Bakeware  
1
IMPORTANT: Never place food or bakeware directly on the oven  
door or bottom. Permanent damage will occur to the porcelain  
finish.  
1. Split-Rack  
2. Removable Insert  
RACKS  
Position racks before turning the oven on. Do not move racks  
with bakeware on them. Make sure racks are level. To move a  
rack, pull it out to the stop position, raise the front edge, then lift  
out. Use the following illustration and chart as a guide.  
To Use Racks:  
1. Place a full rack on position 1 or 2, and the split-rack on  
position 3 or 4.  
2. Place large items on the right side of the full rack.  
3. Place deeper, covered dishes on the left side of the full rack.  
4. Place shallow dishes on the split-rack.  
5
4
3
5. When finished cooking, carefully remove items.  
2
1
FOOD  
RACK POSITION  
Frozen pies, large roasts, turkeys, angel  
food cakes  
1 or 2  
Bakeware  
The bakeware material affects cooking results. Follow  
Bundt cakes, most quick breads, yeast  
breads, casseroles, meats  
2
manufacturers recommendations and use the bakeware size  
recommended in the recipe. Use the following chart as a guide.  
Cookies, biscuits, muffins, cakes, pies  
2 or 3  
BAKEWARE/  
RESULTS  
RECOMMENDATIONS  
BAKEWARE  
I
I
Use temperature and time recommended  
in recipe.  
Light colored  
aluminum  
To cook food evenly, hot air must be able to circulate. Allow 2 in.  
(5 cm) of space around bakeware and oven walls. Use the  
following chart as a guide.  
I
Light golden  
crusts  
I
Even browning  
NUMBER OF  
PAN(S)  
POSITION ON RACK  
May need to reduce baking temperatures  
25°F (15°C).  
Dark aluminum and  
other bakeware  
1
Center of rack.  
with dark, dull and/  
I
I
Use suggested baking time.  
or nonstick finish  
2
Side by side or slightly staggered.  
For pies, breads and casseroles, use  
temperature recommended in recipe.  
I
Brown, crisp  
crusts  
3 or 4  
Opposite corners on each rack. Make sure that no  
bakeware piece is directly over another.  
I
Place rack in center of oven.  
Insulated cookie  
sheets or baking  
pans  
I
I
Place in the bottom third of oven.  
May need to increase baking time.  
I
Little or no  
bottom  
browning  
12  
 
BAKEWARE/  
RESULTS  
RECOMMENDATIONS  
Baking and Roasting  
ACCUBAKE® DUO SYSTEM® Temperature Management  
(on some models)  
I
May need to increase baking time.  
Stainless steel  
I
Light, golden  
crusts  
The ACCUBAKE DUO SYSTEM technology electronically  
regulates the oven heat levels during preheat and bake to  
maintain the most uniform temperature control.  
I
Uneven  
browning  
I
I
Follow manufacturers instructions.  
Stoneware  
Two temperature sensors will independently control the bake and  
broil elements for optimal cooking results. The bake and broil  
elements cycle on and off in intervals. The bake element will glow  
red when cycling on, the broil element will not. This feature is  
automatically activated when the oven is in use.  
I
Crisp crusts  
May need to reduce baking temperatures  
25°F (15°C).  
Ovenproof  
glassware, ceramic  
glass or ceramic  
Before baking and roasting, position racks according to the  
Positioning Racks and Bakewaresection. When roasting, it is  
not necessary to wait for the oven preheat conditioning time to  
end before putting food in unless recommended in the recipe.  
I
Brown, crisp  
crusts  
To Bake or Roast:  
1. Press BAKE.  
Meat Thermometer  
On models without a temperature probe, always rely on a meat  
thermometer to determine doneness of meat and poultry. The  
internal temperature, not appearance, is what counts. A meat  
thermometer is not supplied with this appliance.  
2. Press TEMP or TEMP/TIME upor downarrow pad to set  
a temperature other than 350°F (175°C) in 5 degree amounts.  
The bake range can be set between 170°F and 500°F (75°C  
and 260°C).  
I
I
I
Insert the thermometer into the center of the thickest portion  
of the meat or inner thigh or breast of poultry. The tip of the  
thermometer should not touch fat, bone or gristle.  
When the oven temperature is greater than 170°F (77°C), no  
preheat conditioning time will be shown in the display. The  
preheat conditioning time will not change if the temperature is  
reset before the countdown time ends.  
After reading the thermometer once, push it into the meat  
¹⁄₂ in. (1.25 cm) more and read again. If the temperature  
drops, cook the meat or poultry longer.  
3. Press START. The temperature can be changed after this  
step. START does not need to be pressed again.  
Check all meat in two or three places.  
If baking and roasting while the minute timer is counting  
down, the set temperature can be seen for 5 seconds by  
pressing BAKE.  
Oven Vents  
4. Press CANCEL or OFF when finished.  
Preheating  
2
After START is pressed, the oven will enter a timed preheat  
conditioning. PrE(on some models) and the countdown time  
will appear on the display. When the preheat conditioning time  
ends, a tone will sound and the selected temperature will appear  
on the display.  
1
Preheat temperatures are affected by varying factors such as  
room temperature and peak energy usage times. It is normal for  
the temperature showing on the display and the actual oven  
temperature to differ due to the cycling of the elements.  
2. Ceramic Glass Models  
1. Coil Element Models  
The oven vent releases hot air and moisture from the oven, and  
should not be blocked or covered. Doing so will cause poor air  
circulation, affecting cooking and cleaning results. Never set  
plastics, paper or other items that could melt or burn near the  
oven vent.  
Waiting an additional 10 minutes, after the preheat conditioning  
time ends, to put food in the oven is suggested when baking  
foods with leavening ingredients, such as yeast, baking powder,  
baking soda and eggs.  
On coil element models, the element can be used when the oven  
is in use as long as the cookware does not extend more than 1 in.  
(2.5 cm) over the element.  
®
Choice Bake Function  
(on some models)  
The CHOICE BAKE® function eliminates the top heat during oven  
cooking. It is ideal for baking pies, casseroles and breads, and for  
roasting foods that require longer and slower cook times such as  
poultry and roasts.  
Similar to the baking and roasting function, the bake elements or  
burners cycle on and off at intervals during CHOICE BAKE®  
cycle. However, the cycle duration for the broil element is much  
shorter during CHOICE BAKE®, allowing less top browning of  
foods and more customized control for your baking results.  
13  
 
To Use:  
To Broil:  
1. Press CUSTOM BROIL.  
1. Press CHOICE BAKE® function.  
Press the TEMP upor downarrow pad to set a  
temperature other that 350°F (175°C) in 5 degree amounts.  
The bake range can be set between 170°F and 500°F (75°C  
and 260°C).  
2. Press START.  
3. Press CANCEL when finished.  
To Custom Broil:  
1. Press CUSTOM BROIL.  
2. Press START.  
The temperature can be changed after this step. Start does  
not need to be pressed again.  
2. Press TEMP upor downarrow pad to change the  
temperature in 5° amounts. The broil range can be set  
between 300°F and 500°F (150°C and 260°C).  
3. Press OFF/CANCEL when finished cooking.  
3. Press START.  
To use the CHOICE BAKE® function during a regular BAKE cycle  
to achieve less top browning, press CHOICE BAKE® function, set  
the desired temperature and press START.  
On some models, if broiling while the time is counting down,  
the set broiling temperature can be seen for 5 seconds by  
pressing CUSTOM BROIL.  
4. Press CANCEL when finished.  
Broiling  
Broiling uses direct radiant heat to cook food. Changing the  
temperature when Custom Broiling allows more precise control  
when cooking. The lower the temperature, the slower the  
cooking. Thicker cuts and unevenly shaped pieces of meat, fish  
and poultry may cook better at lower broiling temperatures.  
BROILING CHART  
For best results, place food 3 in. (7 cm) or more from the broil  
element. Times are guidelines only and may need to be adjusted  
for individual foods and tastes. Recommended rack positions are  
numbered from the bottom (1) to the top (5). For diagram, see the  
Positioning Racks and Bakewaresection.  
I
Use only the broiler pan and grid provided with the range. It is  
designed to drain juices and help prevent spatter and smoke.  
COOK  
RACK  
POSITION  
TIME  
I
For proper draining, do not cover the broiler grid with foil. The  
bottom of the pan may be lined with aluminum foil for easier  
cleaning.  
FOOD  
minutes  
Side 1  
Side 2  
I
I
Trim excess fat to reduce spattering. Slit the remaining fat on  
the edges to prevent curling.  
Steak  
1 in. (2.5 cm) thick  
medium rare  
medium  
4
4
4
14-15  
15-16  
18-19  
7-8  
Pull out oven rack to the stop position before turning or  
removing food. Use tongs to turn food to avoid the loss of  
juices. Very thin cuts of fish, poultry or meat may not need to  
be turned.  
8-9  
well done  
9-10  
*Ground meat patties  
³ꢀ₄ in. (2 cm) thick  
well done  
I
After broiling, remove the pan from the oven when removing  
the food. Drippings will bake on the pan if left in the heated  
oven, making cleaning more difficult.  
4
4
13-14  
20-22  
7-8  
Pork chops  
1 in. (2.5 cm) thick  
10-11  
Before broiling, position rack according to Broiling Chart. It is not  
necessary to preheat the oven before putting food in unless  
recommended in the recipe. Position food on grid in the broiler  
pan, then place it in the center of the oven rack. Close the door to  
the broil stop position to ensure proper broiling temperature.  
Ham slice, precooked  
¹ꢀ₂ in. (1.25 cm) thick  
4
4
8-10  
5-7  
4-5  
3-4  
Frankfurters  
Lamb chops  
1 in. (2.5 cm) thick  
4
14-17  
8-9  
Chicken  
bone-in pieces  
boneless breasts  
3
4
17-20  
11-16  
17-20  
11-16  
Fish  
- ¹ꢀ₂ in.  
4
4
8-10  
4-5  
8-9  
Fillets ¹ꢀ₄  
(.6-1.25 cm) thick  
- 1 in.  
16-18  
Steaks ³ꢀ₄  
(2-2.5 cm) thick  
*Place up to 9 patties, equally spaced, on broiler grid.  
14  
 
Warm Hold Feature  
Timed Cooking  
(on some models)  
(on some models)  
WARNING  
WARNING  
Food Poisoning Hazard  
Food Poisoning Hazard  
Do not let food sit in oven more than one hour  
before or after cooking.  
Do not let food sit in oven more than one hour  
before or after cooking.  
Doing so can result in food poisoning or  
sickness.  
Doing so can result in food poisoning or  
sickness.  
IMPORTANT: Food must be at serving temperature before  
placing it in the warmed oven. Food may be held up to one hour,  
however breads and casseroles may become too dry if left in the  
oven during Warm Hold.  
Timed Cooking allows the oven to be set to turn on at a certain  
time of day, cook for a set length of time, and/or shut off  
automatically. Delay start should not be used for food such as  
breads and cakes because they may not bake properly.  
Warm Hold Feature allows hot cooked foods to stay serving  
temperature. It can also be used at the end of a timed cook.  
Style 1 Series Electronic Oven Control (see Electronic  
Oven Controlssection)  
To Use Automatic Warm Hold Feature:  
At the end of a timed cook, either with or without a delayed start,  
or at the end of a sequence program in which the last step is not  
the Warm Hold mode, the oven will automatically default to a  
1-hour warm hold mode at 170°F (77°C).  
To Set a Timed Cook:  
1. Press BAKE (optional).  
2. Press the TEMP upor downarrow pads to enter a  
temperature other than the one displayed.  
When the cook time ends or the last step of the sequence is  
complete, the display will show a warming countdown time.  
When warming ends, the oven will automatically shut off and  
Endwill appear on the display. Four tones will sound, and then  
four 1-second reminder tones will sound every minute thereafter.  
3. Press STOP TIME.  
4. Press the HR and MIN upor downarrow pads to enter  
the desired time to end cooking.  
5. Press START. The display will count down the time.  
To Disable Automatic Warm Hold: Press and hold WARM for 5  
seconds. Offwill appear in the 4-digit display. Repeat to turn  
back on.  
When the time ends, the oven will shut off automatically and  
Endwill appear on the display. End-of-cycle tones will  
sound, then, if enabled, reminder tones will sound every  
minute.  
When using the Automatic Warm Hold Feature, cook times may  
need to be adjusted accordingly so that foods do not become  
overcooked and dry.  
6. Open and close the oven door to clear the display and/or  
stop reminder tones.  
To Use Manual Warm Hold Feature:  
To Set a Delayed Timed Cook:  
1. Press WARM.  
Before setting, make sure the clock is set to the correct time of  
2. Set the temperature (optional).  
day. See Clocksection.  
Press the TEMP upor downarrow pad to raise or lower  
the temperature in 5°F (3°C) amounts to set a temperature  
other than 150°F (66°C). The warm range is 100°F-200°F  
(38°C-93°C).  
1. Press desired cook function.  
2. Press the TEMP upor downarrow pads to enter a  
temperature other than the one displayed.  
3. Press START TIME or DELAY START TIME.  
3. Press START.  
4. Press the HR and MIN upor downarrow pads to enter  
4. Press OFF/CANCEL when finished.  
the time of day to start.  
5. Press STOP TIME (optional).  
6. If STOP TIME has been pressed, press the HR and MIN up”  
or downarrow pads to enter the desired time to end  
cooking.  
7. Press START. DELAYwill appear on the display.  
When the start time is reached, the oven will automatically  
turn on. When the stop time is reached (if programmed), the  
oven will shut off automatically and Endwill appear on the  
display. End-of-cycle tones will sound, then, if on, reminder  
tones will sound every minute.  
8. Open and close the oven door to clear the display and/or  
stop reminder tones.  
15  
 
To Program the First Step of the Sequence:  
1. Press FIRST/NEXT STEP.  
Style 2 Series Electronic Oven Control (see Electronic  
Oven Controlssection)  
PROGRAMand STEPwill appear on the display. A  
flashing 1will also appear on the display, indicating that  
step 1 is being programmed.  
To Set a Timed Cook:  
1. Press BAKE. The bake indicator light will light up.  
2. Set the temperature (optional).  
2.  
Choose the desired cook function by pressing any cook  
function key.  
3. Press START TIME, then HR and MIN upor downarrow  
3. Press the TEMP/TIME upor downarrow pad to enter a  
pads to set the time of day for the first cook function to begin.  
temperature other than the one displayed.  
If START TIME is not pressed, then the sequence of cook  
functions will begin immediately once programming is  
complete and START is pressed.  
4. Press COOK TIME. The cook time oven indicator light will  
light up.  
5. Press TEMP/TIME upor downarrow pad to enter the  
The display will show either the time of day (if start time was  
not programmed) or the start time (if same was programmed),  
but with a flashing colon. Stopand Timewill also appear  
on the display.  
length of time to cook.  
6. Press START/ENTER. The display will count down the time.  
When the time ends, the oven will shut off automatically and  
Endwill appear on the display.  
4. Press STOP TIME, then HR and MIN upor downarrow  
7. Press OFF or open the oven door to clear the display.  
pads to set the time of day for the first cook function to stop.  
To Set a Delayed Timed Cook:  
Before setting, make sure the clock is set to the correct time of  
day. See Clocksection.  
To Program Next Steps of the Sequence:  
1. Press FIRST/NEXT STEP.  
PROGRAMand STEPwill appear on the display. The  
number of the steps being programmed will flash.  
1. Press BAKE.  
2. Set the temperature (optional).  
STARTand TIMEwill appear on the display.  
3. Press the TEMP upor downarrow pad to enter a  
temperature other than the one displayed.  
2. Choose the desired cook function by pressing any cook  
function key.  
4. Press COOK TIME. The cook time oven indicator light will  
light up.  
Press TEMP upor downarrow pad (if desired) to select  
temperature.  
5. Press the TEMP/TIME upor downarrow pad to enter the  
length of time to cook.  
3. Press STOP TIME, then HR and MIN upor downarrow  
6. Press START TIME. The start time/delay oven indicator light  
pads to select stop time.  
will light up.  
4. Press START to begin sequence.  
7. Press the TEMP/TIME upor downarrow pad to enter the  
5. Press OFF/CANCEL at any time to clear program and to stop  
time of day to start.  
program.  
8. Press START/ENTER.  
To Review/Modify Programmed Sequence:  
When the start time is reached, the oven will automatically  
turn on. The temperature and/or time settings can be  
changed any time after pressing START/ENTER by repeating  
steps 1-7. When the set cook time ends, the oven will shut off  
automatically and Endwill appear on the display.  
If program steps are partially or completely programmed, yet the  
sequence has not been started, the programmed cook functions  
can be reviewed.  
1. Press REVIEW STEPS. Step 1 will appear in the display  
9. Press OFF/CANCEL or open the oven door to clear the  
Subsequent presses of REVIEW STEPS will cause display of  
programmed steps in order.  
display.  
STEPand RECALLwill appear on the display. The  
number of the displayed step will flash. A recalled step will  
remain lit on the display for 5 minutes if no further action is  
taken.  
Sequence Programming  
(on some models)  
Sequence Programming allows you to program at one time up to  
four cook functions, and is usable with other electronic oven  
control functions, such as the Timer and Warming Drawer.  
2. If fewer than four steps have been programmed, press  
REVIEW STEPS repeatedly until the last programmed step is  
displayed, then press FIRST/NEXT STEP if it is desired to  
program an additional step.  
Sequence Programming takes precedence over any  
nonsequenced cook function. For example, if an untimed Bake  
function is in process and a sequence program is started, the  
untimed Bake function will be canceled, and the program  
sequence will start.  
While a step is recalled, a cook function pad can be used to  
change the function, or the TEMPERATURE upor down”  
arrow pad can be used to change the set temperature.  
START TIME, when used with the HR or MIN upor down”  
arrow pads, can be used to change, add or delete a delayed  
start.  
All steps of a sequenced program must be programmed with a  
stop time. If a stop time is not entered for a step in the sequence  
program, and the FIRST/NEXT STEP pad is pressed, three tones  
will sound.  
STOP TIME can be used to change the stop time. Changing  
the stop time of a step will automatically change the start  
times and stop times of all subsequent programmed cook  
functions.  
3. After Review/Modification of the programmed sequence is  
complete, press START to begin sequence.  
16  
 
To Modify Sequence Programming:  
1. Press UNDO.  
To Use:  
1. Place cooked food(s) in warming drawer.  
The last step of the sequence will be canceled, and the step  
prior to the canceled sequence will show on the display for  
either review or modification.  
2. Press WARMING DRAWER.  
dr Lo,” “DRAWERand START?will appear on the display.  
3. Press START.  
If the programmed sequence has not been started, see To  
Program Next Steps of the Sequencesection to program a  
step to replace the canceled cook function.  
DRAWERand ONwill appear on the display.  
4. Press DRAWER OFF when finished.  
2. Press START.  
Warming Drawer Settings:  
The first step will show on the display and the program  
sequence will begin.  
The warming drawer is pre-set for a Lotemperature, but can be  
changed by pressing the TEMP uparrow pad. Use the  
following chart as a guide when selecting a different temperature  
other than Lo.”  
Changes can be made during a programmed cook function;  
however, changes cannot be made after a programmed cook  
function has been completed.  
SETTINGS  
TEMPERATURES  
If at any time during an active sequenced program FIRST/  
NEXT STEP is pressed, three tones will sound.  
dr Lo (Low)  
keeps soft rolls warm  
100°F (38°C)  
Warming Drawer  
dr 2 (Medium Low)  
dr 3 (Medium)  
140°F (60°C)  
160°F (71°C)  
180°F (88°C)  
195°F (91°C)  
(on some models)  
dr 4 (Medium High)  
WARNING  
dr HI (High)  
keeps french fries crisp and  
warm  
Food Poisoning Hazard  
Do not let food sit for more than one hour before  
or after cooking.  
Warming Drawer Temperature Chart  
Doing so can result in food poisoning or  
sickness.  
Different foods require different settings in order to maintain the  
ideal serving temperature. Use the following chart as a guide.  
FOOD  
SETTING  
dr HI  
The Warming Drawer is ideal for keeping hot cooked foods at  
serving temperature. It may also be used for warming breads and  
pastries.  
Appetizers  
Biscuits  
Chicken  
dr LO  
Different types of food may be placed in the warming drawer at  
the same time. For best results, do not hold foods longer than  
one hour. For smaller quantities or heat-sensitive foods, such as  
eggs, do not hold longer than 30 minutes.  
Boneless, Breaded  
Nuggets  
dr HI  
dr HI  
Food must be at serving temperature before being placed in the  
warming drawer. Breads, pastries, and fruit pies may be heated  
from room temperature on the HI setting.  
dr LO  
dr HI  
Coffee Cake  
Dinner Plate (1)  
Salisbury Steak, Mashed Potatoes, Corn  
Remove food from plastic bags and place in oven-safe container.  
Cover foods with a lid or aluminum foil.  
Do not cover with plastic wrap.  
Fish Pieces  
Breaded  
Battered  
Empty serving dishes and oven proof dishes can be heated while  
the warming drawer is preheating.  
dr HI  
dr HI  
Before using the warming drawer, wash the tray that lines the  
bottom of the drawer with soap and water. See General  
Cleaningsection.  
dr HI  
dr 4  
French Fries  
Gravy  
The warming drawer comes with a liner that helps keep the  
drawer clean.  
dr 3  
Ham, Boneless  
Hard Rolls  
Lasagna  
Do not place food to be warmed directly on warming drawer liner.  
dr LO  
dr 4  
Pastries  
Prepackaged, baked  
Prepackaged, frozen  
dr 4  
dr LO  
Pie  
Single Crust  
Double Crust  
dr LO  
dr LO  
17  
 
I
I
Remove oven racks to keep them shiny and easy to slide.  
FOOD  
SETTING  
dr 4  
See General Cleaningsection for more information.  
Hand clean inside door edge and the 1½ in. (3.8 cm) area  
around the inside oven cavity frame, being careful not to  
move or bend the gasket. This area does not get hot enough  
during self-cleaning to remove soil. Do not let water, cleaner,  
etc. enter slots on door frame. Use a damp cloth to clean this  
area.  
Pizza  
dr 4  
Potatoes, Baked  
Quiche  
dr 3  
dr 4  
Roast, Boneless  
Roasted Chicken  
Soft Rolls  
I
Wipe out any loose soil to reduce smoke and avoid damage.  
At high temperatures, foods react with porcelain. Staining,  
etching, pitting or faint white spots can result. This will not  
affect cooking performance.  
dr 4  
dr LO  
Prepare Cooktop and Storage Drawer:  
I
Remove plastic items from the cooktop because they may  
melt.  
RANGE CARE  
I
Remove all items from the storage drawer.  
How the Cycle Works  
Self-Cleaning Cycle  
IMPORTANT: The heating and cooling of porcelain on steel in the  
oven may result in discoloring, loss of gloss, hairline cracks and  
popping sounds.  
(on some models)  
The Self-Cleaning cycle uses very high temperatures, burning soil  
to a powdery ash.  
WARNING  
The oven is preset for a 3 hour 30 minute clean cycle, but the  
time can be changed. Suggested clean times are 2 hours 30  
minutes for light soil and between 3 hours 30 minutes and  
4 hours 30 minutes for average to heavy soil.  
Once the oven has completely cooled, remove ash with a damp  
cloth. Do not wipe down any of the inside surfaces until the oven  
has completely cooled down. Applying a cool damp cloth to the  
inner door glass before it has completely cooled could result in  
the glass breaking.  
Burn Hazard  
The oven light will not work during the Self-Cleaning cycle.  
Do not touch the oven during the  
Self-Cleaning cycle.  
To Self-Clean:  
Before self-cleaning, make sure the door is closed completely or  
it will not lock and the cycle will not begin.  
Keep children away from oven during  
Self-Cleaning cycle.  
1. Press AUTO CLEAN.  
2. Press the HR and MIN upor downarrow pad, or the  
TIME/TEMP upor downarrow pad to set a clean time  
other than 3 hours 30 minutes.  
Failure to follow these instructions can result  
in burns.  
On models with style 1 series electronic oven controls (see  
Electronic Oven Controlssection), the oven can be set to a  
clean time between 3 hours 15 minutes and 5 hours 15  
minutes.  
IMPORTANT: The health of some birds is extremely sensitive to  
the fumes given off during the Self-Cleaning cycle. Exposure to  
the fumes may result in death to certain birds. Always move birds  
to another closed and well ventilated room.  
On models with style 2 series electronic oven controls (see  
Electronic Oven Controlssection), the oven can be set to a  
clean time between 2 hours 30 minutes and 4 hours 30  
minutes.  
Self-clean the oven before it becomes heavily soiled. Heavy soil  
results in longer cleaning and more smoke.  
Keep the kitchen well-ventilated during the Self-Cleaning cycle to  
help get rid of heat, odors, and smoke.  
3. Press START/ENTER.  
Do not block the oven vent(s) during the Self-Cleaning cycle. Air  
must be able to move freely. Depending on your model, see  
Oven Ventor Oven Ventssection.  
The oven door will automatically lock. LOCKEDwill appear  
on the display (on some models), and on other models, the  
ON, HEAT and DOOR LOCKED indicator lights will light up.  
The door will not unlock until the oven cools.  
Do not clean, rub, damage or move the oven door gasket. The  
door gasket is essential for a good seal.  
When the cycle is complete and the oven cools, Endwill  
appear on the oven display and LOCKEDshown on the  
display of some models will disappear. The indicator lights on  
other models will go off.  
Prepare Oven:  
I
Remove the broiler pan, grid, cookware and bakeware and,  
on some models, the temperature probe from the oven.  
4. Press CANCEL or OFF/CANCEL, or open the oven door to  
I
Remove any foil from the oven because it may burn or melt,  
damaging the oven.  
clear the oven display.  
18  
 
To Delay Start Self-Clean (on some models):  
CERAMIC GLASS (on some models)  
Before delay starting Self-Clean, make sure the clock is set to the  
correct time of day. See Clocksection. Also, make sure the  
door is closed completely or it will not lock and the cycle will not  
begin.  
Do not use steel wool, abrasive powder cleansers, chlorine  
bleach, rust remover or ammonia because damage may occur.  
Always wipe with a clean, wet cloth or sponge and dry thoroughly  
to prevent streaking and staining.  
1. Press AUTO CLEAN.  
2. Press the HR upor downarrow pad to set a clean time  
other than 3 hours 30 minutes. The clean time can be set  
between 3 hours 15 minutes and 5 hours 15 minutes.  
Cooktop Polishing Creme is recommended regularly to help  
prevent scratches, pitting and abrasions and to condition the  
cooktop, and can be ordered as an accessory. See Assistance  
or Serviceto order.  
3. Press START TIME.  
4. Press the HR and MIN upor downarrows pads to enter  
A Cooktop Scraper is also recommended for stubborn soils, and  
can be ordered as an accessory. See Assistance or Serviceto  
order. The Cooktop Scraper uses razor blades. Store razor  
blades out of the reach of children.  
the time of day to start.  
5. Press START. The time of day is displayed.  
The door will automatically lock and LOCKEDand DELAY”  
will appear on the display. The door will not unlock until the  
oven cools. When the start time is reached, the oven will  
automatically turn on. When the cycle is complete and the  
oven cools, Endwill appear on the lower oven display and  
LOCKEDwill disappear.  
Light to moderate soil  
I
Paper towels or clean damp sponge:  
Clean while the cooktop is still warm. You may want to wear  
oven mitts while doing so.  
6. Press any pad or open the oven door to clear the oven  
Sugary spills (jellies, candy, syrup)  
display.  
I
Cooktop Scraper:  
Clean while the cooktop is still warm. You may want to wear  
oven mitts while doing so.  
To Stop Self-Clean any time:  
Press CANCEL or OFF. If the oven temperature is too high, cln,”  
TIMED,” “ON,” “cool,and LOCKEDwill appear on the display  
(on some models), and the door will remain locked. It will not  
unlock until the oven cools.  
I
Cooktop Polishing Creme and clean damp paper towel:  
Clean as soon as cooktop has cooled down. Rub creme into  
surface with a damp paper towel or soft cloth. Continue  
rubbing until white film disappears.  
General Cleaning  
Heavy soil, dark streaks, specks and discoloration  
IMPORTANT: Before cleaning, make sure all controls are off and  
the oven and cooktop are cool. Always follow label instructions  
on cleaning products.  
I
Cooktop Polishing Creme or nonabrasive cleanser:  
Rub product into soil with a damp paper towel or soft cloth.  
Continue rubbing until white film disappears.  
Soap, water and a soft cloth or sponge are suggested first unless  
otherwise noted.  
Burned-on soil  
I
Cooktop Polishing Creme and Cooktop Scraper:  
EXTERIOR PORCELAIN ENAMEL SURFACES  
Rub creme into soil with damp paper towel. Hold scraper as  
flat as possible on surface and scrape. Repeat for stubborn  
spots. Polish entire cooktop with creme and paper towel.  
(on some models)  
Food spills containing acids, such as vinegar and tomato, should  
be cleaned as soon as the entire appliance is cool. These spills  
may affect the finish.  
Metal marks from aluminum and copper  
I
Cooktop Polishing Creme:  
I
Glass cleaner, mild liquid cleaner or nonabrasive scrubbing  
pad:  
Clean as soon as cooktop has cooled down. Rub creme into  
surface with a damp paper towel or soft cloth. Continue  
rubbing until white film disappears. The marks will not totally  
disappear but after many cleanings become less noticeable.  
Gently clean around the model and serial number plate  
because scrubbing may remove numbers.  
Tiny scratches and abrasions  
STAINLESS STEEL (on some models)  
I
Cooktop Polishing Creme:  
Rub creme into surface with a damp paper towel or soft  
cloth. Continue rubbing until white film disappears. Scratches  
and abrasions do not affect cooking performance and after  
many cleanings become less noticeable.  
Do not use soap-filled scouring pads, abrasive cleaners, Cooktop  
Polishing Creme, steel-wool pads, gritty washcloths or some  
paper towels. Damage may occur.  
Rub in direction of grain to avoid damaging.  
I
I
I
Stainless Steel Cleaner & Polish (not included):  
See Assistance or Servicesection to order.  
Liquid detergent or all-purpose cleaner:  
Rinse with clean water and dry with soft, lint-free cloth.  
Vinegar for hard water spots  
COOKTOP CONTROLS  
Do not use steel wool, abrasive cleansers or oven cleaner.  
Do not soak knobs.  
When replacing knobs, make sure knobs are in the OFF position.  
On some models, do not remove seals under knobs.  
I
Soap and water or dishwasher:  
Pull knobs straight away from control panel to remove.  
19  
 
CONTROL PANEL  
BROILER PAN AND GRID  
Do not use abrasive cleaners, steel-wool pads, gritty washcloths  
or some paper towels. Damage may occur.  
Do not clean in the Self-Cleaning cycle.  
I
Mildly abrasive cleanser:  
I
Glass cleaner and soft cloth or sponge:  
Scrub with wet scouring pad.  
Apply glass cleaner to soft cloth or sponge, not directly on  
panel.  
I
Solution of ¹ꢀ₂ cup (125 mL) ammonia to 1 gal. (3.75 L) water:  
Soak for 20 minutes, then scrub with scouring or steel-wool  
pad.  
COIL ELEMENTS (on some models)  
I
Oven cleaner:  
Do not clean or immerse in water. Soil will burn off when hot.  
Follow product label instructions.  
For more information, see Coil Elements and Burner Bowls.”  
Porcelain enamel only, not chrome  
I
Damp cloth:  
I
Dishwasher  
Make sure control knobs are off and elements are cool.  
STORAGE DRAWER (on some models)  
BURNER BOWLS (on some models)  
Make sure drawer is cool and empty before cleaning.  
I
Solution of ¹ꢀ₂ cup (125 mL) ammonia to 1 gal. (3.75 L) water:  
For more information, see Storage Drawersection.  
Soak for 20 minutes, then scrub with stainless steel-wool  
pad.  
I
Mild detergent  
Drawer Liner (on some models)  
Remove all stored items from drawer and lift out drawer liner.  
I
I
Oven cleaner:  
Follow product label instructions.  
Mildly abrasive cleanser:  
Scrub with wet scouring pad.  
I
Clean with mild detergent.  
WARMING DRAWER and TRAY (on some models)  
Porcelain enamel only, not chrome  
Make sure drawer is cool and remove tray.  
Mild detergent (for both)  
I
Dishwasher  
I
SURFACE UNDER COOKTOP (on some models)  
Oven Light  
Do not remove the cooktop to avoid product damage.  
The oven light is a standard 40-watt appliance bulb. It will come  
on when the oven door is open. It will not work during the Self-  
Cleaning cycle. On some models, when the oven door is closed,  
press OVEN LIGHT to turn it on or off.  
For more information, see Lift-up Cooktopsection.  
I
Steel-wool pad  
Before replacing, make sure the oven and cooktop are cool and  
the control knobs are in the off position.  
OVEN DOOR EXTERIOR  
To replace:  
I
Glass cleaner and paper towels or nonabrasive plastic  
scrubbing pad:  
1. Unplug range or disconnect power.  
2. Turn the glass bulb cover in the back of the oven  
Apply glass cleaner to soft cloth or sponge, not directly on  
panel.  
counterclockwise to remove.  
OVEN CAVITY  
Do not use oven cleaners.  
Food spills should be cleaned when oven cools. At high  
temperatures, foods react with porcelain and staining, etching,  
pitting or faint white spots can result.  
3. Turn bulb counterclockwise to remove from socket.  
4. Replace bulb and bulb cover by turning clockwise.  
5. Plug in range or reconnect power.  
I
I
I
Self-Cleaning cycle:  
See Self-Cleaning Cyclefirst.  
OVEN RACKS AND ROASTING RACKS  
Self-Cleaning cycle:  
See Self-Cleaning Cyclefirst. Remove racks or they will  
discolor and become harder to slide. If this happens, a light  
coating of vegetable oil applied to the rack guides will help  
them slide.  
Steel-wool pad  
20  
 
3. Tilt top of door toward range. Slide hinge hangers down onto  
front frame support pins. Make sure the hinge hangers are  
fully seated and engaged on the support pins.  
Oven Door  
For normal range use, it is not suggested to remove the oven  
door. However, if necessary, follow these instructions. The oven  
door is heavy.  
Before Removing:  
1. Use a putty knife or screwdriver and insert it at the bottom  
corner of the door stop clip.  
4. Insert the door stop clip with the angular surface at the top of  
the frame hinge slot, then push in the bottom of the clip until  
flanges are flush with the front frame.  
2. Pry door stop clip free and remove from front frame hinge  
slot. Take care not to scratch finish.  
3. Repeat procedure for other door stop clip.  
To Remove:  
5. Open the door completely and remove the door removal pins.  
Save door removal pins for future use.  
1. Open the oven door. Insert door removal pins, included with  
your range, into both hinge hangers. Do not remove the pins  
while the door is removed from the range.  
6. Close the door.  
Storage Drawer  
The storage drawer can be removed. Before removing, make sure  
drawer is cool and empty.  
To Remove:  
1. Pull drawer straight out to the first stop.  
2. Lift up the back of the drawer and pull out.  
2. Carefully close the door until it rests against the door removal  
To Replace:  
pins.  
1. Fit the ends of the drawer rails into the guides in the cavity.  
3. Grasp the door on the sides with your fingers on the front of  
2. Slide the drawer closed.  
the door and your thumbs on the inside surface.  
4. Pull door straight up, then toward you. Hinge hangers will  
slide out of front frame hinge slot. Do not remove door  
removal pins until the door is replaced on the range.  
Warming Drawer  
(on some models)  
Remove all items from inside the warming drawer, and allow the  
unit to cool completely before attempting to remove the drawer.  
To Remove:  
1. Open drawer to its full open position.  
2. Locate the black triangle-shaped tabs on both sides of the  
drawer.  
1
1. Tab  
3. Press the tab down on the right side, and lift tab up on the left  
To Replace:  
side at the same time, then pull drawer out another inch.  
1. Grasp the door on the sides with your fingers on the front of  
the door and your thumbs on the inside surface.  
2. Hold oven door so that the top edge of each hinge hanger is  
horizontal. Insert hinge hangers into the front frame hinge  
slots.  
4. Holding the drawer by its sides, not its front, carefully pull it  
all the way out.  
21  
 
To Replace:  
Oven will not operate  
1. Align the drawer glides with the receiving guides.  
I
I
I
Is the electronic oven control set correctly?  
See Electronic Oven Controlsection.  
Has a delay start been set?  
See Timed Cookingsection.  
On some models, is the Control Lock set?  
See Control Locksection.  
2. Push drawer in all the way.  
3. Gently open and close the drawer to ensure it is seated  
Oven temperature too high or too low  
properly on the slides.  
I
I
Does the oven temperature calibration need adjustment?  
See Oven Temperature Controlsection.  
TROUBLESHOOTING  
On some models, does the cooling fan run during BAKE,  
BROIL or CLEAN?  
It is normal for the fan to automatically run when the oven is  
in use. These helps cool the electronic control.  
Try the solutions suggested here first in order to avoid the cost of  
an unnecessary service call.  
Nothing will operate  
Oven indicator lights flash  
I
I
Is the power supply cord unplugged?  
I
Do the oven indicator lights flash?  
Plug into a grounded outlet.  
See the Oven Indicator Lightssection. If the indicator  
light(s) keeps flashing, call for service. See Assistance or  
Servicesection.  
Has a household fuse been blown or has the circuit  
breaker been tripped?  
Replace the fuse or reset the circuit.  
Display shows messages  
Cooktop will not operate  
I
I
Is the display showing PF?  
I
I
Is the control knob set correctly?  
There has been a power failure. Clear the display. See  
Display(s)section. On some models, reset the clock, if  
needed. See Clocksection.  
Push in knob before turning to a setting.  
On ceramic glass models, is the Cooktop Lockoutset?  
See Cooktop Lockoutsection.  
Is the display showing a letter followed by a number?  
Depending on your model, press OFF/CANCEL, OFF or  
CANCEL/OFF to clear the display. See Display(s)section. If  
it reappears, call for service. See Assistance or Service”  
section.  
Excessive heat around cookware on cooktop  
I
Is the cookware the proper size?  
Use cookware about the same size as the surface cooking  
area, element or surface burner. Cookware should not extend  
more than 1 in. (2.5 cm) outside the cooking area.  
Self-Cleaning cycle will not operate  
I
I
I
Is the oven door open?  
Close the oven door all the way.  
Hot Surface indicator light stays on  
Has the function been entered?  
See Self-Cleaning Cyclesection.  
I
Does the Hot Surface indicator light stay on after control  
knob(s) have been turned off?  
See Cooktop Controlssection.  
On some models, has a delay start Self-Clean cycle been  
set?  
See Self-Cleaning Cyclesection.  
Cooktop cooking results not what expected  
I
Has a delay start been set?  
See Timed Cookingsection.  
I
I
I
Is the proper cookware being used?  
See Cookwaresection.  
Is the control knob set to the proper heat level?  
See Cooktop Controlssection.  
Is the appliance level?  
Level the appliance. See the Installation Instructions.  
22  
 
Oven cooking results not what expected  
In the U.S.A.  
Call the Whirlpool Customer Interaction Center  
I
I
I
I
I
I
I
I
I
I
Is the appliance level?  
Level the appliance. See the Installation Instructions.  
toll free: 1-800-253-1301.  
Our consultants provide assistance with:  
Is the proper temperature set?  
I
I
I
I
I
Features and specifications on our full line of appliances.  
Double-check the recipe in a reliable cookbook.  
Installation information.  
Is the proper oven temperature calibration set?  
See Oven Temperature Controlsection.  
Use and maintenance procedures.  
Accessory and repair parts sales.  
Was the oven preheated?  
See Baking and Roastingsection.  
Specialized customer assistance (Spanish speaking, hearing  
impaired, limited vision, etc.).  
Is the proper bakeware being used?  
See Bakewaresection.  
I
Referrals to local dealers, repair parts distributors, and  
service companies. Whirlpool designated service technicians  
are trained to fulfill the product warranty and provide after-  
warranty service, anywhere in the United States.  
Are the racks positioned properly?  
See Positioning Racks and Bakewaresection.  
Is there proper air circulation around bakeware?  
See Positioning Racks and Bakewaresection.  
To locate the Whirlpool designated service company in your  
area, you can also look in your telephone directory Yellow  
Pages.  
Is the batter evenly distributed in the pan?  
Check to make sure batter is level in the pan.  
Is the proper length of time being used?  
Adjust cooking time.  
For further assistance  
If you need further assistance, you can write to Whirlpool  
Corporation with any questions or concerns at:  
Has the oven door been opened while cooking?  
Oven peeking releases oven heat and can result in longer  
cooking times.  
Whirlpool Brand Home Appliances  
Customer Interaction Center  
553 Benson Road  
I
I
Are baked items too brown on the bottom?  
Move rack to higher position in the oven.  
Benton Harbor, MI 49022-2692  
Please include a daytime phone number in your correspondence.  
Are pie crust edges browning early?  
Use aluminum foil to cover the edge of the crust and/or  
reduce baking temperature.  
Accessories U.S.A.  
To order accessories, call the Whirlpool Customer Interaction  
Center toll free at 1-800-442-9991 and follow the menu prompts.  
Or visit our website at www.whirlpool.com and click on Buy  
Accessories Online.”  
ASSISTANCE OR SERVICE  
Before calling for assistance or service, please check  
Troubleshooting.It may save you the cost of a service call. If  
you still need help, follow the instructions below.  
Canning Unit Kit  
(coil element models)  
Order Part #242905  
When calling, please know the purchase date and the complete  
model and serial number of your appliance. This information will  
help us to better respond to your request.  
Cooktop Polishing Creme  
(ceramic glass models)  
Order Part #4392916  
If you need replacement parts  
If you need to order replacement parts, we recommend that you  
only use FSP® replacement parts. FSP® replacement parts will fit  
right and work right because they are made with the same  
precision used to build every new WHIRLPOOL® appliance.  
To locate FSP® replacement parts in your area, call our Customer  
Interaction Center telephone number or your nearest Whirlpool  
designated service center.  
Cooktop Scraper  
(ceramic glass models)  
Order Part #3183488  
Stainless Steel Cleaner & Polish  
(stainless steel models)  
Order Part #4396095  
23  
 
WHIRLPOOL® COOKTOP, BUILT-IN OVEN AND RANGE WARRANTY  
ONE-YEAR FULL WARRANTY  
For one year from the date of purchase, when this appliance is operated and maintained according to instructions attached to or  
furnished with the product, Whirlpool Corporation will pay for FSP® replacement parts and repair labor to correct defects in materials or  
workmanship. Service must be provided by a Whirlpool Corporation designated service company.  
SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON CLEANTOP® COOKTOP  
On ceramic glass ranges and ceramic glass cooktops, in the second through fifth years from the date of purchase, when this appliance  
is operated and maintained according to instructions attached to or furnished with the product, Whirlpool Corporation will pay for FSP®  
replacement parts for the CLEANTOP® ceramic glass cooktop.  
Whirlpool Corporation warrants that the ceramic glass cooktop will not discolor, the cooktop pattern will not wear off, the rubber seal  
between the ceramic glass cooktop and porcelain edge will not crack, the ceramic glass cooktop will not crack due to thermal shock  
and the surface unit elements will not burn out.  
Whirlpool Corporation will not pay for:  
1. Service calls to correct the installation of your appliance, to instruct you how to use your appliance, to replace house fuses or  
correct house wiring, or to replace owner-accessible light bulbs.  
2. Repairs when your appliance is used in other than normal, single-family household use.  
3. Pickup and delivery. Your appliance is designed to be repaired in the home.  
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, improper installation, acts of God or use of products not  
approved by Whirlpool Corporation.  
5. Repairs to CLEANTOP®  
ceramic glass cooktop or other surfaces if they have not been cared for as recommended in the Use and  
Care Guide.  
6. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.  
7. Replacement parts or repair labor costs for units operated outside the United States.  
8. Any labor costs during the limited warranty period.  
WHIRLPOOL CORPORATION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.  
Some states do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or limitation may not  
apply to you. This warranty gives you specific legal rights and you may also have other rights which may vary from state to state.  
Outside the 50 United States, this warranty does not apply. Contact your authorized Whirlpool dealer to determine if another  
warranty applies.  
If you need service, first see the Troubleshootingsection of this book. After checking Troubleshooting,additional help can be found  
by checking the Assistance or Servicesection or by calling the Whirlpool Customer Interaction Center, 1-800-253-1301 (toll-free),  
from anywhere in the U.S.A.  
5/00  
Keep this book and your sales slip together for future  
reference. You must provide proof of purchase or installation  
date for in-warranty service.  
Write down the following information about your appliance to  
better help you obtain assistance or service if you ever need it.  
You will need to know your complete model number and serial  
number. You can find this information on the model and serial  
number label/plate, located on your appliance as shown in the  
Parts and Featuressection.  
Dealer name____________________________________________________  
Address________________________________________________________  
Phone number__________________________________________________  
Model number __________________________________________________  
Serial number __________________________________________________  
Purchase date __________________________________________________  
9756384  
© 2003 Whirlpool Corporation.  
6/03  
Printed in U.S.A.  
All rights reserved.  
® Registered Trademark/TM Trademark of Whirlpool, U.S.A.  
 

Weider Home Gym 831150280 User Manual
Westinghouse Flat Panel Television LD 265 User Manual
Whirlpool Washer 8524742 User Manual
Winegard TV Antenna SS 1000 User Manual
Xantrex Technology Power Supply XPL 18 3 User Manual
Yamaha CD Player CRW8824S User Manual
Yamaha Guitar AES FG User Manual
Yamaha Portable Speaker CBR10 User Manual
Zanussi Freezer ZUT 143W1 User Manual
Zanussi Microwave Oven ZOB 330 User Manual