White Rodgers Thermostat 1A65 User Manual

1A65/1A65W  
ELECTRIC-HEAT THERMOSTAT  
(Single Pole)  
WHITE-RODGERS  
INSTALLATION INSTRUCTIONS  
Operator: Save these instructions for future use!  
FAILURETOREADANDFOLLOWALLINSTRUCTIONSCAREFULLYBEFORE  
INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL  
INJURY AND/OR PROPERTY DAMAGE.  
DESCRIPTION  
The Type 1A65/1A65W Electric Heat Thermostat is de-  
signed for use on all types of electrical heating installa-  
tions such as cable heat, baseboards, wall insert heaters,  
etc. Its narrow operating differential and the ability of its  
fully exposed knob to sense both radiant heat and room  
air temperature make this control ideal for use on such  
installations.  
60  
70  
50  
80  
Dial Setting: Knob may be set anywhere between 40°  
and 85°F by simply turning knob so that indicator on knob  
points to the desired setting.  
PRECAUTIONS  
This control is a precision instrument, and should be All wiring must conform to local and national electrical  
handled carefully. Rough handling or distorting compo- codes and ordinances.  
nents could cause the control to malfunction. Take care  
WARNING  
not to push or damage the knob sensing element  
during installation.  
!
Do not use on circuits exceeding specified volt-  
ages. Higher voltages will damage control and  
could cause shock or fire hazard.  
CAUTION  
!
To prevent electrical shock and/or equipment  
Do not use on inductive loads. Inductive (motor)  
damage, disconnectelectricpower tosystem, at  
loadswilldamagecontrolandcouldcauseshock  
mainfuseorcircuitbreakerbox,untilinstallation  
or fire hazard.  
is complete.  
SPECIFICATIONS  
Temperature Range: 40° to 85°F  
Differential: 1°F  
Switch Rating: Non-Inductive  
22A (2500W) 120 VAC  
22A (5000W) 240 VAC  
18A (5000W) 277 VAC  
Switch Action: Open on rise  
Contact Structure: SPST  
INSTALLATION  
If the heating equipment manufacturer has made provi- 3. It should be mounted as far as possible from undesir-  
sions or recommendations for the location of this control,  
thenfollowthoseinstructions. Ifnot, thefollowingsugges-  
tions should be observed.  
able sources of heat and cold such as:  
a. Windows and doors  
b. Direct rays from sun  
1. The control should be mounted in the wall, approxi-  
mately five feet from the floor, as near as possible to  
the centre of the controlled area.  
c. Hot water or cold water pipes  
d. Adjoining outside walls  
2. It should be mounted on a partitioning wall, not on an  
outside wall.  
WHITE-RODGERS DIVISION  
EMERSON ELECTRIC CO.  
9797 REAVIS RD., ST. LOUIS, MO. 63123  
(314) 577-1300, Fax (314) 577-1517  
PART NO. 37-5427C  
Replaces 37-5427B  
9520  
Printed in U.S.A.  
9999 HWY. 48, MARKHAM, ONT. L3P 3J3  
(905) 475-4653, FAX (905) 475-4625  
 

West Bend Back to Basics Blender BPE3BRAUS User Manual
Western Digital Computer Drive WD10EALX User Manual
Whirlpool Air Conditioner ACE244PT3 User Manual
Whirlpool Washer Dryer LA6058XS User Manual
Whirlpool Washer Dryer WGT3300SQ0 User Manual
Woods Equipment TV Mount BH9000 User Manual
Xerox Projector DP 820 User Manual
Xircom Modem RM56V1 User Manual
Yamaha Musical Instrument CVP 20 User Manual
ZETA Music Systems Musical Instrument Pro Violin User Manual