Zanussi Clothes Dryer TCE7227W User Manual

TUMBLE DRYER  
TCE 7227 W  
0
L
B
K
F
H
Unpacking: see page 15  
INSTRUCTION BOOKLET  
GB  
125985460  
 
Contents  
Something Not Working  
Service and Spare Parts  
Customer Care  
12  
12  
13  
13  
For the User  
Important Safety Information  
2
Installation  
Child Safety  
Use  
Guarantee Conditions  
Adjusting the level of conductivity  
14  
Your New Tumble Dryer  
Description of the Appliance  
The Control Panel  
4
4
5
For the Installer  
Installation Instructions  
Technical Specifications  
15  
15  
Programme Chart  
5
5
5
5
5
6
Low Temperature Button  
Buzzer Off Button  
Unpacking  
15  
15  
16  
16  
16  
Positioning  
Start Button  
Stacking kit (optional accessory)  
Door reversal  
Programme Phase Indicator Lights  
Programme/Time Selector Dial  
Electrical connection  
Programme Chart  
7
8
Operating Sequence  
Hints & Tips on Drying  
Maintenance and Cleaning  
9
10  
External cleaning  
10  
10  
10  
10  
11  
11  
11  
Cleaning the door  
Cleaning fluff filters  
Cleaning the condenser unit  
Emptying the water reservoir  
Cleaning the air intake grille  
Cleaning the drum  
Guide to use the Instruction Book  
The following symbols will be found in the text to guide you throughout the instructions:  
Safety instructions  
Hints and tips  
Environmental information  
3
 
Your New Tumble Dryer  
This tumble dryer will give your wash that soft, relaxed feel whatever the weather.  
Extremely high quality standards both during development and manufacturing  
guarantee a long service life for your appliance.  
Maximum economy in the operation of your dryer is achieved through very frugal  
electricity consumption and short drying times.  
Energy saving tips  
When the appliance is to be scrapped, cut off the  
power supply cable and make the door closing  
device unusable to prevent young children from  
being trapped inside.  
To save energy we recommend that you follow these hints:  
Try to load the maximum capacity of the machine  
as small loads are uneconomical.  
Help to keep your country tidy - use authorised  
Always load well spun laundry. The higher the spin  
speed, the lower the electricity consumption and  
the shorter the drying times.  
disposal sites for your old appliance.  
How do we help to protect the environment? We use  
recycled paper!  
Do not over-dry laundry, this avoids creasing and  
saves energy.  
Old appliance  
Clean the filters regularly to avoid excessive drying  
times and high electricity consumption.  
The symbol  
on the product or on its packaging  
Ventilate the room well. The room temperature  
indicates that this product may not be treated as  
household waste. Instead it shall be handed over to the  
applicable collection point for the recycling of electrical  
and electronic equipment. By ensuring this product is  
disposed of correctly, you will help prevent potential  
negative consequences for the environment and human  
health, which could otherwise be caused by in appropriate  
waste handling of this product. For more detailed  
should not exceed +35°C during drying.  
In the interest  
of the environment  
Materials marked with the symbol  
Check with your local Council or Environmental  
Health Office to see if there are facilities in your  
area for re-cycling this appliance.  
are recyclable.  
information about recycling of this product, please contact  
your local city office, your household waste disposal  
service or the shop where you purchased the product.  
Description of the Appliance  
01 Worktop  
3
1
02 Programme chart  
03 Control panel  
04 Fluff filters  
05 Rating Plate  
06 Condenser unit  
07 Water reservoir  
08 Adjustable feet  
2
7
4
5
4
8
6
4
 
The Control Panel  
1Programme Chart  
5Start button  
This will help you to select the correct programme  
for drying.  
Press this button to start the dryer after having  
selected the programme and the options.  
The relevant light will stop flashing. If you have  
chosen a delayed start, the machine will begin the  
countdown.  
2Low Temperature  
Button  
If the door of the appliance or the small door at  
the bottom is opened while the programme is  
running, this button must be pressed again after  
closing the door in order to restart the programme  
from the point at which it was interrupted.  
This button must be depressed also after a power  
failure and after having re-inserted the water  
reservoir, if it has been emptied in the middle of a  
Pressing this button allows drying to be performed at  
a lower temperature, for delicate items.  
The corresponding pilot light comes on.  
This option can also be used for time controlled  
drying.  
The dryer heats at 1400 W instead of 2200 W.  
If the button is not pressed, drying is performed at  
full power (2200 W).  
programme after lighting up of light  
.
In both cases the light of the Start/Pause button  
flashes to remind you that the start button needs to be  
pressed again.  
This option cannot be selected with QUICK DRY  
.
3QUICK DRY Button  
By depressing this button the drying time is reduced  
6Programme Phase  
Indicator Lights  
in the following COTTON programmes:  
EXTRA DRY  
These lights indicate the various phases of the  
programme as they are being performed.  
READY TO WEAR  
STORE DRY  
“Drying” light  
This light indicates that the appliance is in the drying  
phase.  
The corresponding pilot light comes on.  
This option cannot be selected with LOW  
TEMPERATURE  
function.  
“Cooling” light  
4Buzzer OFF Button  
A buzzer sounds by depressing the push buttons  
during the anti-creasing phase, at the end of  
This light indicates that the appliance is in the  
cooling phase. At the end of drying, there is a  
10 minute cooling phase to cool the laundry.  
programme and when the water reservoir is full.  
Press this button when selecting the programme if  
you wish to switch the buzzer off during the anti-  
creasing phase. The corresponding light illuminates.  
“End of programme” light  
This light is on at the end of the cooling phase,  
during the anti-creasing phase and at the end of the  
programme.  
5
 
“Filter cleaning” light  
7Programme/Time  
Selector Dial  
This light illuminates at the end of the programme to  
remind you that the filters must be cleaned.  
Allows you to select electronically controlled or time  
“Water reservoir full” light  
This light comes on at the end of the programme to  
remind you that the water reservoir must be emptied  
out. If this light illuminates during a programme this  
means that the water reservoir is full. The buzzer  
sounds, the programme stops, the light of the  
Start/Pause button flashes.  
controlled drying.  
Turn the dial to the required programme or time.  
Electronically controlled drying (automatic)  
The appliance runs these programmes with the help  
of probes which detect the degree of dampness of the  
laundry.  
Simply select the programme according to the type of  
laundry and degree of drying required.  
This light comes on also when the water reservoir is  
not inserted correctly.  
“Condenser cleaning” light  
Time controlled drying  
It comes on every 80 cycles to remind you that the  
condenser must be cleaned  
Can be used to finish off drying if necessary.  
Select the 90 or 60 minute programme for cottons or  
the 30 minute programme for synthetics.  
To cancel a programme which is running, turn the  
programme selector dial to “0”.  
At the end of drying, turn the selector dial to “0”  
before removing the laundry.  
6
 
Programme Chart  
Automatic drying (electronic programmes)  
Degree of drying  
Type of laundry  
required  
Max-load (1)  
Programme  
extra dry  
A
B
C(*)  
D
E(*)  
F
7 kg  
7 kg  
7 kg  
7 kg  
7 kg  
7 kg  
ready to wear  
store dry  
slightly damp  
iron dry  
wring dry  
Cotton  
extra dry  
store dry  
iron dry  
3,5 kg  
3,5 kg  
3,5 kg  
G
H(*)  
J
Synthetics  
K
L
Jumpers  
baby dry  
dry fresh  
2 kg  
Jackets, trousers,  
dresses, skirts.  
1 - 4 garments  
(*) According to CEI 1121 Standards.  
• Baby cycle “K” is a special programme for jumpers to be dried “ready to wear”.  
• Dry fresh “L” is designed to clean and freshen garments labelled “dry clean only” and “hand wash” at home,  
in your tumble dryer, using the special product available on the market.  
Time controlled drying  
Programme  
Type of laundry  
Cotton  
Drying time  
Max-load (1)  
selector dial position  
90 min  
60 min  
30 min  
7 kg  
90’  
Cotton  
60’  
30’  
7 kg  
Synthetics  
3,5 kg  
(1) Never overfill the drum (do not load large quilts, for example).  
Drying times vary according to:  
• The type of laundry  
• The size of the load  
• The degree of spinning prior to drying.  
• The degree of of dryness required  
Fresh & Cool  
This position on the programme selector dial can be used to freshen the laundry (e.g. to remove a persistent  
odour of moth-balls).  
Load  
It is often difficult to estimate the weight of items to be dried. We therefore recommend that you adopt the  
following guidelines:  
cotton, linen: drum full but not too tightly packed;  
synthetics: drum no more than half full;  
delicate fabrics: drum no more than one third full.  
7
 
Operating Sequence  
All drying programmes end with a 10 minute  
cooling phase light is on).  
You may remove the laundry after this phase.  
The lights and illuminate.  
Before using your tumble dryer for the first time, we  
recommend to place a few damp cloths inside the  
appliance and dry for 30 minutes.  
There may be dust inside a brand new tumble dryer.  
,
Drying  
8. If the laundry is not removed at the end of the  
cycle, the dryer performs an anti-creasing phase  
(duration: 30 minutes maximum).  
1. Connect the appliance.  
2. Open the door (see picture).  
If you do not remove the laundry, the dryer will stop  
automatically at the end of the anti-creasing phase.  
Lights  
,
and  
remain lit and the buzzer  
sounds every 10 seconds for 2 minutes.  
The light of the “START/PAUSE” button goes  
off and a flashing zero appears on the display.  
9. Turn the programme selector dial to “0”; all the  
P1149  
P1108  
lights go out. The appliance is switched off.  
Remove the laundry.  
3. Load the items one at a time, shaking them out  
loosely.  
4. Close the door. Please check the laundry does not  
get caught between the door and filter.  
If you open and then close the door before  
turning the selector dial to “0” all the lights  
corresponding to the phases making up the  
performed programme come on and the  
display shows the duration of the programme.  
5. Select the drying programme or time. The lights  
,
and  
come on. The light of the  
“START/PAUSE” button flashes and the  
display shows the duration of the programme.  
6. If required, press the low temperature button  
and/or the “Buzzer OFF” button or the “Quick  
After each use  
• Clean the filters (see page 10).  
• Empty the water reservoir (see page 11).  
drying” button  
.
7. Press the “START/PAUSE”  
button the  
corresponding light stops flashing and drying  
starts.  
Important!  
If the drying programme has to be stopped before it  
reaches the end, we recommend that you turn the  
programme selector dial to position  
the end of this cooling phase before removing the  
laundry. This will avoid a build-up of heat inside the  
appliance.To do this first turn the dial to “0” and then  
Only the light  
remains lit. If you have selected  
the delayed start, the machine begins its  
countdown.  
If the programme selector dial is turned to another  
position, when the machine is running, the buzzer  
will sound, the programme phase indicator lights  
will flash.  
and wait until  
to  
and depress “START/PAUSE” button  
.
Modifying the programme  
The drum turns alternately in both directions  
during drying.  
To change a programme which is running, first cancel  
it by turning the programme selector dial to “0”.  
Select the new programme and press the  
“START/PAUSE” button.  
8
 
Hints & Tips on Drying  
Before placing articles of laundry in your tumble  
Always load well spun laundry. The higher the spin  
dryer, check the care labels to ensure they are  
recommended for tumble drying.  
speed the lower the electricity consumption and the  
DshOorNteOr tThelodardyidnrgiptpimineg. wet laundry into the dryer.  
Roll the article in a towel or spin to remove excess  
Care Labels you may find on your laundry  
wClaotseer.poppers and zips and fasten any buttons.  
Sort the laundry. Separate synthetics from  
may be tumble dried  
normal drying (high temperature)  
delicate drying (low temperature)  
do not tumble dry  
cRoetmtoonv/leintehnesl,aaunnddrdyryimsempeadraiatetelyly. after the  
Uprsoegarafmabmriechcaosnfdiintiisohneindg. sheet to reduce static. We  
Do not overload the appliance.  
recommend the sheet is pinned to an article of  
lMauixndthrye (luosaidngi.ea. slaarfgeteyapnidn)s.mall articles.  
Here is a list of the approximate weight of some  
common laundry items.  
When drying large items such as sheets, we  
recommend you periodically stop the dryer to  
redistribute the load.  
Sheet  
700 to 1000 g  
Pillowcase  
Tablecloth  
Table Napkin  
Kitchen Towel  
Linen Hand Towel  
Hand Towel  
Bath Towel  
Bathrobe  
100 to 200 g  
400 to 500 g  
50 to 100 g  
DO NOT use the tumble dryer to dry the following:  
Articles contaminated with inflammable substances  
70 to 120 g  
e.g. petrol, cleaning solvents, cooking oil, fats or  
100 to 150 g  
150 to 250 g  
700 to 1000 g  
1000 to 1500 g  
200 to 300 g  
150 to 200 g  
Whaoirollalecnquaenrd. synthetic/wool mixtures unless the  
Viteemryidsellaicbaetleleadrtaisclseusitsaubclhe afosrsitlukm. ble drying.  
Shirt  
Apron  
Very large and bulky items such as duvets or  
sleeping bags.  
9
 
Maintenance and Cleaning  
You must disconnect the appliance from the  
electricity supply, before you can carry out any  
cleaning or maintenance work.  
After a while, a withish patina due to detergent  
residue on laundry forms on the filters. When this  
occurs, clean the filters with warm water using a  
brush. Remove the filter in the door opening as per  
picture (it can be positioned with the tooth facing to  
the left or to the right).  
External cleaning  
Use only soap and water and then dry thoroughly.  
R
S
E
650  
E
R
E
V
-
-
60'  
T
O
50'  
U
00  
A
/
12  
kg 2,5  
kg  
3
5'  
1000  
7
50'  
30  
'
/
-
-
90  
0
95  
'
1
800  
80'  
5
5'  
-
200  
100'  
70  
'
100  
0
/
1
-
6
5'  
0
/
90  
85  
'
800  
70'  
35'  
5'  
0'  
-
5'  
6
3
'
-
-
90  
0'  
45'  
-
kg  
5
5
k
g
2
,
5
Important: do not use methylated spirit, diluents or  
similar products.  
Cleaning the door  
Clean periodically the interior part of the door to  
remove any fluff from the seals around the filter.  
P1152  
Accurate cleaning ensures correct drying.  
R
S
E
650  
E
R
E
V
-
-
60'  
T
O
50'  
U
00  
A
/
12  
kg 2,5  
kg  
3
5'  
1000  
7
50'  
30  
'
/
-
-
90  
0
95  
'
1
800  
80'  
5
5'  
-
200  
100'  
70  
'
100  
0
/
1
-
6
5'  
0
/
90  
85  
'
800  
70'  
35'  
5'  
0'  
-
5'  
6
3
'
-
-
90  
0'  
45'  
-
kg  
5
5
k
g
2
,
5
Do not use the appliance without filters.  
Cleaning the condenser  
unit  
Clean the condenser when light  
cleaning) comes on.  
(Condenser  
P1150  
The condenser is situated at the lower part of the  
cabinet behind a small door. To open the door, push  
the catch as per picture.  
Cleaning the filters  
Your dryer will only function well if the filters are  
clean.  
The filters collect all the fluff which accumulates  
during drying and they must therefore be cleaned at  
the end of each programme, before removing the  
laundry, with a damp cloth.  
P1153  
The light  
(Filter cleaning) is on to remind you to  
carry out this operation.  
During the drying cycle or at the end, it is normal for  
water to be present on the surface of the condenser  
insertion.  
S
E
650  
E
R
E
V
-
-
60'  
T
O
R
50'  
30  
'
U
A
/
120  
95  
0
kg 2,5  
kg  
3
5'  
1000  
7
0
'
/
-
-
90  
1
800  
5'  
-
/
120  
0
'
1
00'  
70  
'
65'  
1000  
6
80  
5'  
-
5
0'  
/
90  
0
85  
'
800  
70'  
35'  
5'  
-
5
90  
0'  
'
-
-
45'  
-
3
0'  
kg  
5
5
k
g
2
,
5
To pull out the condenser, first turn the two red stops  
downwards and then remove the condenser unit  
holding it at the handle.  
P1151  
P1110  
The filter in the inner door must be removed for  
cleaning.  
Do not be alarmed by the amount of fluff. It is not  
due to excessive wear caused by the dryer. All fabric  
loses fluff when drying but it goes un-noticed in the  
air. In a tumble dryer it simply collects in the filter.  
P1155  
P1154  
10  
 
Clean it with a brush and rinse it under the shower if  
necessary.  
“START/PAUSE” button has to be depressed  
again to allow the programme to continue.  
Handy tip: The condensed water may be used in a  
steam iron or to top up a battery, etc. In this case it  
must be filtered (e.g. through a coffee filter).  
Cleaning the air intake  
grille  
Using a vacuum cleaner remove the fluff from the air  
intake grille at the back of the appliance.  
P0639  
Also clean the outside, removing all fluff.  
Clean the rubber seal round the condenser cabinet  
and in the inner part of the small door with a damp  
cloth.  
Important! Do not use pointed objects or utensils to  
clean the spaces between the plates, as this could  
damage the condenser and make it permeable.  
Re-fit the condenser, turn the red stops upwards and  
close the door.  
P1162  
Do not use this appliance if the condenser  
has not been fitted.  
Cleaning the drum  
When your laundry does not reach the desired degree  
of dryness, in other words, when it turns out either  
too dry or too damp, we advise you to clean the  
inside of the drum with a cloth soaked with vinegar.  
This will eliminate the slight patina that has formed  
in the drum (due to residues of detergent and  
softeners used in the washing, and to the lime  
contained in the water), which prevents the probes  
from detecting the correct degree of dryness.  
Emptying the water  
reservoir  
Water extracted from the laundry condenses inside  
the machine and is collected in a reservoir.  
The reservoir must be emptied after each drying  
cycle to ensure efficient operation when the machine  
is next used. The pilot light  
reminds you this operation.  
(Water reservoir full)  
Proceed as follows:  
• Pull out the reservoir  
• Turn it upside down and let water flow down  
• Re-fit the reservoir  
P1157  
P1156  
The reservoir must be re-inserted correctly.  
If this is not done the pilot light  
comes on during  
next drying and the programme stops, leaving the  
laundry damp. The buzzer will sound.  
After emptying and inserting the reservoir the  
11  
 
Something Not Working  
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without  
calling out an engineer. Before contacting your local Service Centre, please carry out the checks listed below.  
IMPORTANT: if you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or  
installation, a charge will be made even if the appliance is under guarantee.  
Possible causes  
Symptom  
The door(s) has (have) not been closed.  
The plug is not properly inserted in the power socket.  
There is no current at the socket.  
The tumble dryer does not start  
The main fuse or the fuse in the plug has blown.  
The selector dial is not set correctly.  
The water reservoir is full or not properly inserted  
(the pilot light  
is on ).  
The Start Button  
has not been depressed.  
The laundry has not been spun properly.  
The filters and/or the condenser are clogged up.  
The water reservoir is full.  
Drying takes too long or laundry is not  
dry enough.  
The room temperature is too high.  
The selected time or drying cycle was not suitable  
fTohrethloewlatuenmdprye.rature button  
has been pressed.  
There is too much laundry inside the appliance.  
The dryer is not correctly installed.  
If after the above checks, there is still a fault, call your local Service Force Centre.  
Before calling out an engineer, please ensure you  
Service & Spare Parts  
have read the details under the heading “Something  
In the event of your appliance requiring service, or if  
you wish to purchase spare parts, please contact your  
local Service Force Centre by telephoning:  
Not Working”.  
When you contact the Service Force Centre you will  
need to give the following details:  
1. Your name, address and post code  
2. Your telephone number  
0870 5 929929  
Your telephone call will be automatically routed to  
the Service Force Centre covering your post code  
area.  
For the address of your local Service Force Centre  
and further information about Service Force, please  
3. Clear and concise details of fault  
4. The model and serial number of the appliance  
(found on the rating plate)  
5. The purchase date.  
Please note that a valid purchase receipt or  
guarantee documentation is required for in-  
guarantee service calls.  
For Customer Service in Ireland please contact us at  
the address below:  
Zanussi Electrolux  
Electrolux Group (Irl) Ltd  
Long Mile Road  
Dublin 12  
Republic of Ireland  
Tel: +353 (0)1 4090751  
12  
 
Customer Care Department  
Major Appliances  
Addington Way  
Luton  
Bedfordshire  
LU4 9QQ  
Customer Care Department  
For general enquiries concerning your Zanussi  
Electrolux appliance or for further information on  
Zanussi Electrolux products, please contact our  
Customer Care Department by letter or telephone at  
the address below or visit our website at  
Tel 08705 727727*  
To buy accessories, consumables and spare parts at  
our online shop please visit: http://www.zanussi-  
electrolux.co.uk  
* calls to this number may be recorded for training  
purposes.  
Guarantee Conditions  
Appliances found to be in use within a  
Standard guarantee conditions  
commercial environment, plus those which are  
We, Zanussi Electrolux, undertake that if, within 12  
months of the date of the purchase, this ZANUSSI  
ELECTROLUX appliance or any part thereof is  
proved to be defective by reason only of faulty  
workmanship or materials, we will, at our option  
repair or replace the same FREE OF ANY CHARGE  
for labour, materials or carriage on condition that:  
subject to rental agreements.  
Products of Zanussi Electrolux manufacture  
which are NOT marketed by Zanussi Electrolux.  
European guarantee  
If you should move to another country within Europe  
then your guarantee moves with you to your new  
home subject to the following qualifications:  
The appliance has been correctly installed and  
used only on the electricity supply stated on the  
rating plate.  
The guarantee starts from the date you first  
purchased your product.  
The appliance has been used for normal domestic  
purposes only, and in accordance with the  
The guarantee is for the same period and to the  
manufacturer’s instructions.  
same extent for labour and parts as exists in the  
new country of use for this brand or range of  
products.  
The appliance has not been serviced, maintained,  
repaired, taken apart or tampered with, by any  
person not authorised by us.  
The guarantee relates to you and cannot be  
transferred to another user.  
Your new home is within the European  
Community (EC) or European Free Trade Area.  
The product is installed and used in accordance  
with our instructions and is only used  
domestically, i.e. a normal household.  
The product is installed taking into account  
regulations in your new country.  
All service work under this guarantee must be  
undertaken by a Service Force Centre.  
Any appliance or defective part replaced shall  
become the Company’s property.  
This guarantee is in addition to your statutory and  
other legal rights.  
Home visits are made between 8.30am and 5.30pm  
Monday to Friday. Visits may be available outside  
these hours in which case a premium will be  
charged.  
Before you move please contact your nearest  
Customer Care Centre, listed below, to give them  
details of your new home. They will then ensure that  
the local Service Organisation is aware of your move  
and able to look after you and your appliances.  
France  
Germany  
Italy  
Sweden  
UK  
Ireland  
Exclusions  
This guarantee does not cover:  
Senlis  
+33 (0) 344 62 29 29  
+49 (0) 800 234 7378  
+39 0434 39 4700  
Damage or calls resulting from transportation,  
improper use or neglect, the replacement of any  
light bulbs or removable parts of glass or plastic.  
Nurnberg  
Pordenone  
Stockholm  
Luton  
+46 (0) 8 672 53 90  
Costs incurred for calls to put right an appliance  
which is improperly installed or calls to  
appliances outside the United Kingdom.  
+44 (0)  
+353 (0)1 4090751  
8705 727727  
Dublin  
13  
 
Adjusting the level of conductivity  
Water contains, a variable quantity of limestone and  
mineral salts of which quantities vary according to  
geographical locations thus varying its conductivity  
values.  
Relevant variations of the conductivity of the water  
compared to those prefixed by the factory could  
slightly influence the residual humidity of the  
laundry at the end of the cycle.  
Adjusting the level of conductivity:  
Press the START/PAUSE  
button sequentially:  
the level of conductivity is indicated by the phase  
pilot lights, which light in various combinations as  
follows:  
Approximate value  
LED lit  
Conductivity  
µS/cm  
Your dryer allows you to regulate the sensitivity of  
the drying sensor based on conductivity values of the  
water by using the following procedure.  
Low  
< 300  
Medium  
High  
300 - 600  
> 600  
To access adjustment mode:  
Turn the programme selector dial to switch on the  
appliance. In selection mode, press simultaneously  
the buttons 1 and 3.  
Normally, the appliance is factory-set to the highest  
level; however, certain models may be configured  
differently.  
Press the buttons down until the pilot lights above  
each ones begin to flash and one of the pilot lights  
indicating the drying phase lights , cooling  
,
or  
end cycle  
remains lit.  
Memorizing the new setting:  
Simultaneously press the buttons 1 and 3.  
Press the buttons down until the pilot lights above  
each ones stop flashing and the buzzer sounds.  
1
3
4
2
14  
 
Installation Instructions  
It is dangerous to alter the specifications or  
attempt to modify this product in any way.  
Any electrical work required to install this  
appliance should be carried out by a qualified  
electrician or competent person.  
Care must be taken to ensure that the appliance  
does not stand on the electrical supply cable.  
Technical Specifications  
DIMENSIONS  
Height  
Width  
Depth  
85 cm (33.5”)  
60 cm (23.6”)  
58 cm (22.8”)  
POWER SUPPLY VOLTAGE  
TOTAL POWER ADSORBED  
240 V/50 Hz  
2450 W (13A)  
MAX LOAD CAPACITY  
Cotton, linen  
Synthetics  
7.kg (13.2 lbs)  
3,5 kg (06.6 lbs)  
DRUM VOLUME  
CONSUMPTIONS  
108 l  
Cotton, linen  
Cotton, linen  
Synthetics  
3.95 kWh (7, kg store dry)  
3.05 kWh (7, kg iron dry)  
1.45 kWh (3,5 kg store dry)  
This appliance complies with the following E.E.C. Directives:  
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications;  
- 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.  
Positioning  
Unpacking  
It is recommended that, for your convenience, the  
machine is positioned close to your washing  
machine.  
Warning !  
Slide out the polythene bag containing the  
The tumble dryer must be installed in a clean place,  
where dirt does not build up.  
Air must be able to circulate freely all round the  
appliance. Do not obstruct the front ventilation grille  
or the air intake grilles at the back of the machine.  
polystyrene block before using the appliance.  
Pull off adhesive strips from inside machine  
on top of drum  
To keep vibration and noise to a minimum when the  
dryer is in use, it should be placed on a firm, level  
surface.  
Once in its permanent operating position, check that  
the dryer is absolutely level with the aid of a spirit  
level. If it is not, raise or lower the feet until it is.  
The feet must never be removed.  
Do not restrict the floor clearance through deep-  
pile carpets, strips of wood or similar. This might  
cause heat build-up which would interfere with  
the operation of the appliance.  
P1106  
Should the appliance be moved, it must be  
transported vertically.  
15  
 
Important  
Before switching on, make sure the electricity supply  
voltage is the same as that indicated on the  
The hot air emitted by the tumble dryer can reach  
temperatures of up to 60°C. The appliance must  
therefore not be installed on floors which are not  
resistant to high temperatures.  
When operating the tumble dryer, the room temperature  
must not be lower than +5°C and higher than +35°C, as  
it may affect the performance of the appliance.  
appliance’s rating plate. (See picture on page 4).  
The appliance is supplied with a 13amp plug fitted.  
In the event of having to change the fuse in the plug  
supplied, a 13amp ASTA approved BS 1363/A fuse  
must be used.  
Should the plug need to be replaced for any reason,  
proceed as described below. The wires in the mains lead  
are coloured in accordance with the following code:  
Stacking kit (optional accessory)  
It should be possible to stack your new dryer on top  
of a front loading washing machine with a worktop  
depth between 48 and 60 cm.  
Green and Yellow  
Blue  
Brown  
- Earth  
- Neutral  
- Live  
Read carefully the instructions supplied with the kit.  
GREEN & YELLOW  
Please contact your local Service Force Centre for  
further advice.  
E
L
N
BROWN  
BLUE  
CORD CLAMP  
P1041  
The wire coloured green and yellow must be  
connected to the terminal marked with the letter «E»  
P1148  
or by the earth symbol  
yellow.  
or coloured green and  
The wire coloured blue must be connected to the  
terminal «N» or coloured black.  
The wire coloured brown must be connected to the  
terminal marked «L» or coloured red.  
Upon completion there must be no cut, or stray  
strands of wire present and the cord clamp must be  
secure over the outer sheath.  
Door reversal  
To make it easier to load or unload the laundry the  
door can be reversed.  
This operation must be carried out by qualified  
personnel.  
Please contact the nearest Zanussi Service Force  
Centre.  
This will be a chargeable option.  
WARNING:  
A cut off plug inserted into a 13 amp socket  
is a serious safety (shock) hazard.  
Ensure that the cut off plug is disposed of  
safely.  
Electrical connection  
Any electrical work required to install this appliance  
should be carried out by a qualified electrician or  
competent person.  
WARNING: THIS APPLIANCE MUST BE  
EARTHED.  
The manufacturer declines any liability  
should this safety measure not be observed.  
Should the appliance power supply cable  
need to be replaced, this must be carried out  
by our Service Centre.  
Permanent connection  
In the case of permanent connection it is necessary  
that you install a double pole switch between the  
appliance and the electricity supply (mains), with a  
minimum gap of 3mm between the switch contacts  
and of a type suitable for the required load in  
compliance with the current electrical regulations.  
The switch must not break the yellow and green  
earth cable at any point.  
The power supply cable must be accessible  
after installing the machine.  
16  
 
From the Electrolux Group. The world’s No. 1 choice.  
The Electrolux Group is the world's largest producer of powered appliances for kitchen, cleaning and outdoor  
use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines,  
vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in  
more than 150 countries around the world.  
© Electrolux plc 2006  
 

Weider Home Gym WEBE13011 User Manual
Westinghouse Computer Monitor LCM 20v5 User Manual
Whirlpool Washer 6LA932OXTWO User Manual
Whirlpool Washer WTW5500SQ0 User Manual
Wolf Microwave Oven MW24 User Manual
Xantech Stereo Amplifier PA1235 User Manual
Yamaha Electronic Keyboard CP5 User Manual
Zanussi Cooktop ZKC5020 User Manual
Zanussi Oven 238500 User Manual
Zanussi Refrigerator HB2P4CR User Manual