User
Manual
Washing
machine
ZWH 5105
ZWH 5125
Safety information
In the interest of your safety and to ensure
the correct use, before installing and first
using the appliance, read this user manual
carefully, including its hints and warnings.
To avoid unnecessary mistakes and
accidents, it is important to ensure that all
people using the appliance are thoroughly
familiar with its operation and safety
features. Save these instructions and make
sure that they remain with the appliance if it
is moved or sold, so that everyone using it
through its life will be properly informed on
appliance use and safety.
● Always unplug the appliance and turn off the
water supply after use, clean and
maintenance.
● Under no circumstances should you attempt
to repair the machine yourself. Repairs
carried out by inexperienced persons may
cause injury or serious malfunctioning.
Contact your local Service Centre. Always
insist on genuine spare parts.
Installation
● This appliance is heavy. Care should be
taken when moving it.
● When unpacking the appliance, check that it
is not damaged. If in doubt, do not use it and
contact the Service Centre.
● All packing and transit bolts must be
removed before use. Serious damage can
occur to the product and to property if this is
not adhered to. See relevant section in the
user manual.
● After having installed the appliance, check
that it is not standing on the inlet and drain
hose and the worktop is not pressing the
electrical supply cable.
● If the machine is situated on a carpeted floor,
please adjust the feet in order to allow air to
circulate freely
General safety
● It is dangerous to alter the specifications or
attempt to modify this product in any way.
● During high temperature wash programmes
the door glass may get hot. Do not touch it!
● Make sure that small pets do not climb into
the drum. To avoid this, please check into
the drum before using.
● Any objects such as coins, safety pins, nails,
screws, stones or any other hard, sharp
material can cause extensive damage and
must not be placed into the machine.
● Only use the advised quantities of fabric
softener and detergent. Damage to the fabric
can ensue if you over-fill. Refer to the
manufacturer’s recommendations of
quantities.
● Always be sure, that there is no water
leakage from hoses and their connections
after the installation.
● Wash small items such as socks, laces,
washable belts etc in a washing bag or
pillow case as it is possible for such items to
slip down between the tub and the inner
drum.
● Do not use your washing machine to wash
articles with whalebones, material without
hems or torn material.
● If the appliance is installed in a location
subject to frost, please read the «dangers of
freezing» chapter.
● Any plumbing work required to install this
appliance should be carried out by a
qualified plumber or competent person.
● Any electrical work required to install this
appliance should be carried out by a
qualified electrician or competent person.
3
● The packaging components (e.g. plastic film,
polystyrene) can be dangerous to children -
danger of suffocation! Keep them out of
children’s reach
● Keep all detergents in a safe place out of
children’s reach.
● Make sure that children or pets do not climb
into the drum. To avoid that they remain
trapped inside, this the machine incorporates
special feature.
Use
● This appliance is designed for domestic use.
It must not be used for purposes other than
those for which it was designed.
● Only wash fabrics which are designed to be
machine washed. Follow the instructions on
each garment label.
● Do not overload the appliance. See the
relevant section in the user manual.
● Before washing, ensure that all pockets are
empty and buttons and zips are fastened.
Avoid washing frayed or torn articles and
treat stains such as paint, ink, rust, and
grass before washing. Underwired bras must
NOT be machine washed.
● Garments which have been in contact with
volatile petroleum products should not be
machine washed. If volatile cleaning fluids
are used, care should be taken to ensure
that the fluid is removed from the garment
before placing in the machine.
● Never pull the power supply cable to remove
the plug from the socket; always take hold of
the plug itself.
● Never use the washing machine if the power
supply cable, the control panel, the working
surface or the base are damaged so that the
inside of the washing machine is accessible.
To activate this
device, rotate the
button (without
To disable this
device and restore
the possibility of
pressing it) inside the closing the door,
door clockwise until
the groove is
rotate the button anti-
clockwise until the
groove is vertical.
horizontal. If
necessary use a coin.
Child safety
● This appliance is not intended for use by
person (including children) with reduced
physical sensory or mental capabilities or
lack of experience and knowledge unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
● This washing machine is not intended for
use by young children or infirm persons
without supervision.
● Young children should be supervised to
ensure that they do not play with the
appliance.
4
Description of the appliance
1
Detergent dispenser drawer
1
2
2
Control panel
3
Door opening handle
4
Drain pump
5
Adjustable feet
3
4
5
Detergent dispenser drawer
Prewash
Wash
SM001
Fabric Softener
5
Control panel and functions
Inicio Diferido
Lavado
Off
Algodón
60°Eco
60°
40°
9h
3h
6h
Centrifugado
Descarga
90°
1000
900
Aclarados
Prelavado
Diario
700
Frío
30°
Aclarado/Centrif.
Fin
500
30°
Frío
60°
Agua
en Cuba
Super
Rápido
Lana 40°
Frío
40°
30°
40°
30°
Delicados
Planchado
fácil
Frío
Sintéticos
6 7
1
2 3 4
5
Symbols:
Info
= Handwash
The programme selector dial, the different
buttons and the programme progress display
will be indicated in all the book with the
relevant numbers given in this table.
Frío = Cold wash
Programme selector dial and
On/Off switch
●
The programme selector dial allows to select a programme
and/or to switch the machine on/off.
1
2
●
Press this button repeatedly to change the spin speed, if you
want your laundry to be spun at a speed different from the
one proposed by the washing machine or to select «Rinse
Hold» option. The relevant light will light up.
Spin reduction button
Rinse Hold
Option button
●
●
By means of this button, you can select only one of the
options.
The relevant light will light up.
3 Prewash / Daily / Super Quick
●
By means of this button, the machine performs some
additional rinses.
Extra rinse button
Start/Pause button
4
5
●
●
This button allows to start the selected programme; the
corresponding green pilot light stops flashing.
This button interrupts also a programme which is running,
the corresponding green pilot light starts to flash.
6
●
●
The different pilot lights illuminate depending on the running
programme phase.
Programme progress display
Delay Start button
6
7
This button allows to delay the starting of the washing
programme by 3, 6, and 9 hours.
Functions
OPTIONS
Extra Rinse (Button 4 - AquaCare)
The machine performs some additional rinses
during the washing cycle. This option is
recommended for people who are allergic to
detergents, and in areas where the water is
very soft.
RINSE HOLD (Button 2)
By selecting this option the water of the last rinse
is not emptied out to prevent the fabrics from
creasing. When the programme has finished, the
door is blocked to indicate that the water must be
emptied out. To empty out the water see
Programme progress display (6)
chapter «At the end of the programme».
Prewash (Button 3)
Main
Select this option if you wish your laundry to be
prewashed at 30°C before the main wash.
The prewash ends with a short spin in
programmes for Cotton and Synthetic fabrics,
whereas in the programmes for Delicate fabrics
the water is only drained.
Lavado
wash (A)
Rinses/
Spin (B)
Aclarado/Centrif.
End (C)
Fin
The light A illuminates after pressing button 5.
The light B is on when the machine is rinsing
or spinning.
The light C illuminates at the end of the
washing cycle.
Daily (Button 3)
This option can be used for lightly soiled
Cotton, Synthetic or Delicate items in order to
obtain a good washing performance in a short
time.
Super Quick (Button 3)
Short cycle for lightly soiled items or for laundry
which needs only freshening up.
We recommend you to reduce the fabrics
loading.
7
Programme table
Programme/
Temperature
Description of
programme
Type of laundry
Options
Spin / Rinse Hold,
Prewash/Daily/
Super Quick,
Main wash
WHITE COTTONS
90°
White cotton (heavily
soiled items)
Rinses
Long spin at the max
spin speed
Extra Rinse
White and fast coloured
cotton (normally soiled
cotton items)
Main wash
Rinses
Long spin at the max
spin speed
WHITE/COLOURED
COTTONS
Spin / Rinse Hold,
Prewash,
Extra Rinse
60°Eco
ECONOMY
Spin / Rinse Hold,
Prewash/Daily/
Super Quick,
Main wash
WHITE/COLOURED
COTTONS
White and coloured
cotton (normally soiled
cotton items)
Rinses
Long spin at the max
spin speed
60° - 40° - 30° - Cold
Extra Rinse
Spin / Rinse Hold,
Prewash/Daily/
Super Quick,
Main wash
Rinses
Short spin
SYNTHETICS
Synthetic or mixed
fabrics
60° - 40° - 30° - Cold
Extra Rinse
SYNTHETICS
EASY IRON
40°
Spin / Rinse Hold,
Prewash
Synthetic or mixed
fabrics (delicate items)
EASY IRON
Main wash
RInses
Short spin
Extra Rinse
Spin / Rinse Hold,
Prewash/Daily/
Super Quick,
Main wash
Rinses
Short spin
DELICATES
Delicate items
40°- 30° - Cold
Extra Rinse
Programme for wool
«Pure new wool, non-
shrink, machine
Main wash
Rinses
WOOL
40°
Spin /Rinse Hold
Spin /Rinse Hold
Short spin
washable» label
Special programme
delicate fabrics with the
«hand washing» care
symbol
Main wash
Rinses
Short spin
HANDWASH
30° - Cold
8
Programme table
Programme/
Temperature
Description of
programme
Type of laundry
Options
Separate rinses cycle
with softener, if needed,
for hand washed cotton
items
Rinses
Long spin at the max
speed
Spin /Rinse Hold,
Extra Rinse
RINSES
For emptying out the
water
DRAIN
SPIN
Draining of water
Long spin at the max
speed for hand washed
cotton items
Spin
Drain and long spin
Off
To interrupt a running programme, to cancel an
incorrect option selection or to switch the machine
off,
Cancelling /
Switching off
of the machine
Max loads
Max loads (with option):
Cottons ...................................................7.0 kg
Synthetics................................................3,5 kg
Delicates ................................................3,5 kg
Easy Iron ...............................................1,5. kg
Wool .......................................................2.0 kg
Handwash ...............................................2.0 kg
Cottons + Super Quick . . . . . . . . . . . . . .3,5 kg
Synthetics + Super Quick . . . . . . . . . . .1,5 kg
Delicates + Super Quick . . . . . . . . . . . .1,5 kg
9
Programme information
Selecting this programme the laundry is gently washed and spun to
avoid any creasing. In this way ironing is easier. Furthermore the
machine will perform additional rinses.
Easy Iron
Rinses
With this separate programme it is possible to rinse and spin cotton
garments which have been washed by hand. The machine performs
3 rinses, followed by a final spin at maximum speed. The spin speed
can be reduced by depressing button 2.
For emptying out the water at the end of a programme with Rinse
Hold option.
Turn first the programme selector dial to «Off», then select
programme «Drain» and depress the button 5.
Drain
Spin
Separate spin for cotton items washed by hand.
According to the type of fabric, it is possible to choose a different
speed by means of the relevant button from one proposed by the
machine. This programme can be selected for emptying out the water
at the end of a programme with Rinse Hold option.
10
Washing hints
Sorting the laundry
Maximum loads
Follow the wash code symbols on each
garment label and the manufacturer’s washing
Recommended loads are indicated in the
programme charts.
instructions. Sort the laundry as follows: whites, General rules:
coloureds, synthetics, delicates, woollens.
Cotton, linen: drum full but not too tightly
packed;
Synthetics: drum no more than half full;
Delicate fabrics and woollens: drum no more
than one third full.
Washing a maximum load makes the most
efficient use of water and energy.
For heavily soiled laundry, reduce the load
size.
Temperatures
for normally soiled white cottons
90° or 95°
50°/60°
and linen (e.g. tea cloths, towels,
tablecloths, sheets...)
for normally soiled, colour fast
garments (e.g. shirts, night
dresses, pyjamas....) in linen,
cotton or synthetic fibres and for
lightly soiled white cotton (e.g.
underwear).
Laundry weights
The following weights are indicative:
bathrobe
napkin
quilt cover
sheet
pillow case
tablecloth
1200 g
100 g
700 g
500 g
200 g
250 g
200 g
100 g
200 g
100 g
600 g
200 g
500 g
100 g
100 g
for delicate items (e.g. net
curtains), mixed laundry including
synthetic fibres and woollens
bearing the label «pure new wool,
machine washable, non-shrink».
30°-40°
Before loading the laundry
Never wash whites and coloureds together.
Whites may lose their «whiteness» in the
wash.
New coloured items may run in the first wash;
they should therefore be washed separately
the first time.
Make sure that no metal objects are left in
the laundry (e.g. hair clips, safety pins,
pins). Button up pillowcases, close zip
fasteners, hooks and poppers. Tie any belts
or long tapes.
Remove persistent stains before washing.
Rub particularly soiled areas with a special
detergent or detergent paste.
Treat curtains with special care. Remove hooks
or tie them up in a bag or net.
towelling towel
tea cloth
night dress
ladies’ briefs
man’s work shirt
man’s shirt
man’s pyjamas
blouse
men’s underpants
Removing stains
Stubborn stains may not be removed by just
water and detergent. It is therefore advisable to
treat them prior to washing.
Blood: treat fresh stains with cold water. For
dried stains, soak overnight in water with a
special detergent then rub in the soap and
water.
11
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and
dab the stain; treat several times.
etc.), the colour, washing temperature and
degree of soiling.
All commonly available washing machine
detergents may be used in this appliance:
Dried grease stains: moisten with turpentine,
lay the garment on a soft surface and dab the
stain with the fingertips and a cotton cloth.
Rust: oxalic acid dissolved in hot water or a
rust removing product used cold. Be careful
with rust stains which are not recent since the
cellulose structure will already have been
damaged and the fabric tends to hole.
Mould stains: treat with bleach, rinse well
(whites and fast coloureds only).
Grass: soap lightly and treat with bleach
(whites and fast coloureds only).
Ball point pen and glue: moisten with
acetone (*), lay the garment on a soft cloth and
dab the stain.
Lipstick: moisten with acetone as above, then
treat stains with methylated spirits. Remove
any residual marks from white fabrics with
bleach.
Red wine: soak in water and detergent, rinse
and treat with acetic or citric acid, then rinse.
Treat any residual marks with bleach.
Ink: depending on the type of ink, moisten the
fabric first with acetone (*), then with acetic
acid; treat any residual marks on white fabrics
with bleach and then rinse thoroughly.
Tar stains: first treat with stain remover,
methylated spirits or benzine, then rub with
detergent paste.
● powder detergents for all types of fabric,
● powder detergents for delicate fabrics (60°C
max) and woollens,
● liquid detergents, preferably for low
temperature wash programmes (60°C max)
for all types of fabric, or special for woollens
only.
The detergent and any additives must be
placed in the appropriate compartments of the
dispenser drawer before starting the wash
programme.
If using concentrated powder or liquid
detergents, a programme without prewash
must be selected.
The washing machine incorporates a
recirculation system which allows an optimal
use of the concentrated detergent.
Pour liquid detergent into the dispenser drawer
compartment marked
the programme.
just before starting
Any fabric softener or starching additives must
be poured into the compartment marked
before starting the wash programme.
Follow the product manufacturer’s
recommendations on quantities to use and do
not exceed the «MAX» mark in the
detergent dispenser drawer.
(*) do not use acetone on artificial silk.
Detergents and additives
Good washing results also depend on the
choice of detergent and use of the correct
quantities to avoid waste and protect the
environment. Although biodegradable,
detergents contain substances which, in large
quantities, can upset the delicate balance of
nature.
The choice of detergent will depend on the
type of fabric (delicates, woollens, cottons,
12
Quantity of detergent to be used
Degrees
Level Characteristic
The type and quantity of detergent will depend
on the type of fabric, load size, degree of
soiling and hardness of the water used.
Water hardness is classified in so-called
«degrees» of hardness. Information on
hardness of the water in your area can be
obtained from the relevant water supply
company, or from your local authority.
Follow the product manufacturers’ instructions
on quantities to use.
German
°dH
French
°T.H.
1
2
3
4
soft
medium
hard
0-7
0-15
16-25
26-37
> 37
8-14
15-21
> 21
very hard
Use less detergent if:
● you are washing a small load,
● the laundry is lightly soiled,
Degrees of water hardness
Follow the product manufacturers’ instructions
● large amounts of foam form during washing.
on quantities to use.
13
Before the first use
WARNING!
Ensure that the electrical and water
connections comply with the installation
instructions.
IMPORTANT!
Remove the polystyrene block and any
material from the drum.
IMPORTANT!
We recommend you to pour 2 litres of water into
the main wash compartment
of the
,
detergent drawer in order to activate the ECO
valve. Than run a cotton cycle at 90°C, without
any laundry in the machine, to remove any
manufacturing residue from the drum and tub.
Pour 1/2 a measure of detergent into the
dispenser drawer and start the machine.
14
Operating sequence
ATTENTION!
Load the laundry
If you turn the programme selector dial to
another programme when the machine is
working, the red pilot light of button 5 will flash
3 times to indicate a wrong selection. The
machine will not perform the new selected
programme.
Open the door by
carefully pulling the
door handle outwards.
Place the laundry in the
drum, one item at a
time, shaking them out
as much as possible. Close the door.
Select the spin speed or Rinse Hold option
by pressing button 2
Measure out the detergent and the fabric
softener
The relevant light will light up.
When selecting a programme, the light
corresponding to the maximum speed allowed
for that programme will illuminate (refer to the
section «Programme table» for the maximum
allowed spin speed).
Select the desired option by means of
buttons 3 and 4
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent required,
pour it into the main wash compartment
and, if you wish to carry out a programme with
the prewash phase, pour it into the
Depending on the programme, different
functions can be combined. These must be
selected after choosing the desired programme
and before pressing the button 5.
For the compatibility of the options with the
washing programmes, refer to the section
«Programme table».
compartment marked
.
If required, pour fabric softener into the
compartment marked
(the amount used
must not exceed the «MAX» mark in the
drawer). Close the drawer gently.
Start the programme by pressing button 5
To start the selected programme, press this
button; the corresponding green pilot light
stops flashing.
Select the required programme by means of
the programme selector dial (1)
Turn the programme selector dial to the
required programme.
The green light of button 5 starts to flash.
It can be turned either clockwise or
anticlockwise.
On programme progress display the pilot light
A illuminates to indicate that the appliance
starts operating and the door is locked.
IMPORTANT!
On position «Off» the programme is reset and
the machine is switched Off.
If an option which is not compatible with the set
wash programme is selected, the red light of
this button flashes for 3 times.
At the end of the programme the selector
dial must be turned to position «Off», to
switch the machine off.
15
Select the delayed start by pressing button
7
Altering an option or a running programme
It is possible to change any option before the
programme carries it out.
Before you make any change, you must pause
the washing machine by pressing the button 5.
Changing a running programme is possible
only by resetting it. Turn the programme
selector dial to «Off» and then to the new
programme position. Start the new programme
by depressing the button 5 again.
The washing water in the tub will not empty
out.
This option permits to delay the start of the
wash programme by 3, 6, 9 hours.
Press this button repeatedly to select the
required delay. The relevant light illuminates.
You must select this option after you have set
the programme and before you press the
button 5.
Cancelling the delayed start:
You can cancel the delay time at any moment,
before you press the button 5.
Interrupting a programme
If you have already pressed the button 5, and
you wish to cancel the delay time, proceed as
follows:
Press the button 5 to interrupt a programme
which is running, the corresponding light starts
to flash. Press the button again to restart the
programme.
●
●
●
set the washing machine to PAUSE by
pressing the button 5;
press the button 7 once, the light relevant to
the selected delay goes off.
press the button 5 again to start the
programme.
Cancelling a programme
Turn the selector dial to «Off» to cancel a
programme which is running. Now you can
select a new programme.
IMPORTANT!
Opening the door after the programme has
started
●
The selected delay can be modified only
after you have turned the programme
First set the machine to pause by pressing the
button 5.
selector dial to the «Off» position and after
you have selected the programme again.
The door will be locked throughout the delay
time. If you need to open the door, you must
first set the washing machine to PAUSE by
pressing the button 5 and wait few minutes
before opening the door. After you have
closed the door, press the button 5 again.
After some minutes, the door can be opened.
●
If the machine is already heating, that the
water level is above the bottom edge of the
door, the door cannot be opened.
If you cannot open the door but you need to
open it you have to switch the machine off by
turning the selector dial to «Off». After few
minutes the door can be opened
(Pay attention to the water level and
temperature!).
After this procedure, it will be necessary to set
the programme and the options again and then
press the button 5.
Note!
The Delay Start cannot be selected with
DRAIN programme.
16
At the end of the programme
The machine stops automatically.
The pilot light of button 5 go off while the
phase light C illuminates. The door can be
opened.
If at the end of a programme there is water in the
tub (and the door is locked) to empty out the
water follow the following instructions:
●
●
●
turn the programme selector dial to «Off»
select the «Drain» or «Spin» programme
reduce the spin speed if needed, by means
of the relevant button
●
press button 5
At the end of the cycle, turn the programme
selector dial to «Off» to switch the machine off.
Remove the laundry from the drum and
carefully check that the drum is empty.
If you do not intend to carry out another wash,
close the water tap.
Leave the door open to prevent the formation
of mildew and unpleasant smells.
17
Care and cleaning
IMPORTANT!
Remove the drawer by pressing the catch
downward and by pulling it out. Flush it out
under a tap, to remove any traces of
accumulated powder.
You must DISCONNECT the appliance from
the electricity supply, before you can carry out
any cleaning or maintenance work.
Cleaning the drawer recess
Descaling
The water we use normally contains lime. It is
a good idea to periodically use a water
softening powder in the machine. Do this
separately from any laundry washing, and
according to the softening powder
Having removed the
drawer, use a small
brush to clean the
recess, ensuring that
all washing powder
manufacturer's instructions. This will help to
prevent the formation of lime deposits.
residue is removed
from the upper and
lower
Maintenance Wash
part of the recess.
With the use of low temperature washes it is
possible to get a build up of residues inside the
drum.
We recommend that a maintenance wash be
performed on a regular basis.
Replace the drawer and run the rinse
programme without any clothes in the drum.
Cleaning the pump
The pump should be inspected if
To run a maintenance wash:
●
the machine does not empty and/or spin
the machine makes an unusual noise during
draining due to objects such as safety pins,
coins etc. blocking the pump.
●
●
●
The drum should be empty of laundry.
Select the hottest cotton wash programme.
Use a normal measure of detergent, must be
a powder with biological properties.
●
Proceed as follows:
●
Disconnect the appliance.
If necessary wait until the water has cooled
down.
External cleaning
Clean the exterior cabinet of the appliance with
soap and water only, and then dry thoroughly.
●
●
Open the pump
Cleaning the dispenser drawer
door.
The washing powder and additive dispenser
drawer should be cleaned regularly.
● Place a container
close to the pump to
collect any spillage.
● Pull out the
emergency emptying
hose, place it in the
container and remove its cap.
●
When no more water comes out, unscrew the
pump cover and remove it. Always keep a
rag nearby to dry up spillage of water when
removing the cover.
To aid cleaning, the top part of the additive
compartment should be removed.
18
The dangers of freezing
If the machine is exposed to temperatures
below 0°C, certain precautions should be taken.
●
●
●
Turn off the water tap.
Unscrew the inlet hose.
Place the end of the emergency emptying
hose and that of the inlet hose in a bowl
placed on the floor and let water drain out.
Screw the water inlet hose back on and
reposition the emergency emptying hose
after having put the cap on again.
When you intend to start the machine up
again, make sure that the room temperature
is above 0°C.
●
●
Remove any objects from the pump impeller
by rotating it.
Put the cap back on the emergency emptying
hose and place the latter back in its seat.
● Screw the pump
●
●
cover fully in.
● Close the pump
door.
IMPORTANT!
Every time you drain the water through the
emergency emptying hose you must pour 2
litres of water into the main wash compartment
of the detergent drawer and then run the drain
programme. This will activate the ECO VALVE
device avoiding that part of the detergent
remains unused at next washing.
IMPORTANT!
When the appliance is in use and depending
on the programme selected there can be hot
water in the pump.
Never remove the pump cover during a wash
cycle, always wait until the appliance has
finished the cycle, and is empty. When
replacing the cover, ensure it is securely
retightened so as to stop leaks and young
children being able to remove it.
Emergency emptying out
If the water is not discharged, proceed as
follows to empty out the machine:
●
●
●
pull out the plug from the power socket;
close the water tap;
if necessary, wait until the water has cooled
down;
●
●
open the pump door;
Cleaning the water inlet filter
place a bowl on the floor and place the end
of the emergency emptying hose into the
bowl. Remove its cap. The water should
drain by gravity into the bowl. When the bowl
is full, put the cap back on the hose. Empty
the bowl. Repeat the procedure until water
stops flowing out;
If your water is very hard or contains traces of
lime deposit, the water inlet filter may become
clogged. It is therefore a good idea to clean it
from time to time.
Turn off the water tap.
Unscrew the water
inlet hose. Clean the
filter using a hard
bristle brush.
●
●
●
clean the pump if necessary as previously
described;
replace the emergency emptying hose in its
seat after having plugged it;
screw the pump cover again and close the
door.
Tighten up the inlet
hose.
19
Something not working
IMPORTANT!
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily
without calling out an engineer. Before contacting your local Service Centre, please carry out the
checks listed below.
During machine operation it is possible that the red pilot light of button 5 flashes to indicate that
the machine is not working.
Once the problem has been eliminated, press the button 5 to restart the programme. If after all
checks, the problem persists, contact your local Service Centre.
Malfunction
Possible Cause / Solution
The door has not been closed. (Red pilot light
flashes)
●
Close firmly the door.
The plug is not properly inserted in the power socket.
Insert the plug into the power socket.
There is no power at the socket.
Please check your domestic electrical installation.
The main fuse has blown.
Replace the fuse.
●
●
The washing machine does not start:
●
The selector dial is not correctly positioned and the
button 5 has not been pressed.
●
Please turn the selector dial and press the button 5
again.
The button 7 has been selected.
●
If the laundry are to be washed immediately, cancel
the delay start
The water tap is closed. (Red pilot light flashes)
Open the water tap.
●
The inlet hose is squashed or kinked. (Red pilot light
flashes)
Check the inlet hose connection.
●
The machine does not fill:
The filter in the inlet hose is blocked. (Red pilot light
flashes)
●
Clean the water inlet hose filter.
The door is not properly closed. (Red pilot light
flashes)
Close firmly the door.
●
20
Malfunction
Possible Cause / Solution
The end of the drain hose is too low.
Refer to relevant paragraph in «water drainage»
section.
The machine fills then empties
immediately:
●
The drain hose is squashed or kinked. (Red pilot
light flashes)
●
Check the drain hose connection.
The drain pump is clogged. (Red pilot light flashes)
Clean the drain pump.
The laundry is not evenly distributed in the drum.
Redistribute the laundry.
The RINSE HOLD option has been selected.
●
The machine does not empty and/or
does not spin:
●
●
Disable the option.
●
Select the option DRAIN or SPIN.
Too much detergent or unsuitable detergent (creates
too much foam) has been used.
●
Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the
inlet hose fittings. It is not always easy to see this as
the water runs down the hose; check to see if it is
damp.
There is water on the floor:
●
Check the water inlet hose connection.
The inlet hose is damaged.
●
Change it with a new one.
The cap on the emergency emptying hose has not
been replaced after cleaning the pump.
●
Put the cap back on the emergency emptying and
place the latter back in its seat.
Too little detergent or unsuitable detergent has been
used.
●
Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to
washing.
●
Use commercial products to treat the stubborn
stains.
Unsatisfactory washing results:
The correct temperature was not selected.
Check if you have selected the correct temperature.
Excessive laundry load.
Introduce into the drum less laundry.
●
●
21
Malfunction
Possible Cause / Solution
The programme is still running.
Wait the end of washing cycle.
The door lock has not been released.
Wait until the door is released.
There is water in the drum.
Select drain or spin programme to empty out the water.
●
The door will not open:
●
●
The transit bolts and packing have not been
removed.
●
Check the correct installation of the appliance.
The support feet have not been adjusted.
Check the correct levelling of the appliance.
The laundry is not evenly distributed in the drum.
Redistribute the laundry.
Maybe there is very little laundry in the drum.
Load more laundry.
●
The machine vibrates or is noisy:
●
●
The electronic unbalance detection device has cut in
because the laundry is not evenly distributed in the
drum. The laundry is redistributed by reverse rotation
of the drum. This may happen several times before
the unbalance disappears and normal spinning can
resume. If, after 10 minutes, the laundry is still not
evenly distributed in the drum, the machine will not
spin. In this case, redistribute the load manually and
select the spin programme.
Spinning starts late or the machine
does not spin:
●
Redistribute the laundry.
The machine is fitted with a type of motor which
makes an unusual noise compared with other
traditional motors. This new motor ensures a softer
start and more even distribution of the laundry in the
drum when spinning, as well as increased stability of
the machine.
The machine makes an unusual noise
No water is visible in the drum
Machines based on modern technology operate very
economically using very little water without affecting
performance.
22
If you are unable to identify or solve the
problem, contact our service centre.
Before telephoning, make a note of the model,
serial number and purchase date of your
machine: the Service Centre will require this
information.
Mod. ... ... ...
Prod. No. ... ... ...
Ser. No. ... ... ...
Technical data
Dimensions
Width
60 cm
85 cm
63 cm
Height
Depth (including the porthole)
Electrical connection Voltage -
Overall power - Fuse
Information on the electrical connection is given on the rating
plate on the inner edge of the appliance door
Water supply pressure
Minimum
Maximum
0,05 MPa
0,8 MPa
Maximum Load
Spin Speed
Cotton
7
kg
Maximum
0
1000 rpm (ZWH 5105)
1200 rpm (ZWH 5125)
23
Consumption values
Energy
consumption
(in kWh)
Water
consumption
(in litres)
Programme
duration
Programme
2.1
1.19
1.4
65
59
60
155
145
120
Cotton 90°
Cotton 60°Eco
Cotton 60°
Synthetics 60°
1.05
0.45
57
65
100
90
Synthetics 40° Easy Iron
Delicates 40°
Wool 40°
0.6
0.4
63
55
70
60
Handwash 30°
0.35
0.1
-
55
42
55
45
Rinse
Drain
Spin
-
-
2
10
-
(*) The Cotton 60°Eco with a load of 7 kg is
the reference programme for the data
entered in the energy label, in compliance
with EEC 92/75 standards.
Infos
The consumption data shown on this chart is to
be considered purely indicative, as it may vary
depending on the quantity and type of laundry,
on the inlet water temperature and on the
ambient temperature. It refers to the highest
temperature for each wash programme.
24
Installation instruction
Unpacking
All transit bolts and packing must be removed
before using the appliance.
You are advised to keep all transit devices so
that they can be refitted if the machine ever
has to be transported again.
polystyrene block fitted with the adhesive
tape on the door seal.
6. Fill the smaller upper hole and the two large
ones with the corresponding plastic plug
caps supplied in the bag containing the
instruction booklet.
Positioning
Install the machine on a flat hard floor. Make
sure that air circulation around the machine is
not impeded by carpets, rugs etc. Check that the
machine does not touch the wall or other kitchen
units. Level the washing machine by raising or
lowering the feet. The feet may be tight to adjust
as they incorporate a self locking nut, but the
machine MUST be level and stable.
Any necessary adjustment can be made with a
spanner.
Accurate levelling prevents vibration, noise and
displacement of the machine during operation.
Never place cardboard, wood or similar materials
under the machine to compensate for any
unevenness in the floor.
HEC0030
1. After removing all the packaging, carefully
lay machine on it’s back to remove the
polystyrene base from the bottom.
2. Remove the power supply cable and the
hoses from the hose holders on the rear of
the appliance.
If necessary, check the
setting with a spirit
level.
HEC0036
HEC0037
3. Unscrew the three bolts.
4. Slide out the relevant plastic spacers.
Water inlet
Do not use the hose from your previous
machine to connect to the water supply.
5. Open the porthole, take out the inlet hose
from the drum and remove the polystyrene
block fitted with the adhesive tape on the
door seal.Open the porthole, take out the
inlet hose from the drum and remove the
HEC0025
25
In a sink drain pipe branch. This branch
must be above the trap so that the bend is at
least 60 cm above the ground.
Attention!
Do not place the inlet hose downward.
Angle the hose to the left or right depending
on the position of your water tap.
1. Set the hose correctly by loosening the ring
nut. After positioning the inlet hose, be sure to
tighten the ring nut again to prevent leaks.
Directly into a drain pipe at a height of not
less than 60 cm and not more than 90 cm.
The end of the drain hose must always be
ventilated, i.e. the inside diameter of the drain
pipe must be larger than the outside diameter
of the drain hose.
2. Connect the hose to
a tap with a 3/4”
thread. Always use the
hose supplied with the
appliance.
The drain hose must not be kinked.
Electrical connection
This machine is designed to operate on a 230-
240 V, single-phase, 50 Hz supply.
Check that your domestic electrical installation
can take the maximum load required (2.2 kW),
also taking into account any other appliances
in use.
The inlet hose must not be lengthened. If it is
too short and you do not wish to move the tap,
you will have to purchase a new, longer hose
specially designed for this type of use.
Attention!
Connect the machine to an earthed socket.
Water drainage
The end of the drain hose can be positioned in
three ways:
The manufacturer declines any responsibility
for damage or injury through failure to comply
with the above safety precaution.
Hooked over the
edge of a sink using
the plastic hose
guide supplied with
the machine. In this
case, make sure the
Attention!
Should the appliance power supply cable need
to be replaced, this MUST be carried out by
our Service Centre.
end cannot come
unhooked when the
machine is emptying. This could be done by
tying it to the tap with a piece of string or
attaching it to the wall.
Attention!
Please ensure that when the appliance is
installed it is easily accessible for the engineer
in the event of a breakdown.
26
Environmental concerns
Packaging materials
Ecological hints
To save water, energy and to help protect the
environment, we recommend that you follow
these tips:
The materials marked with the symbol
recyclable.
>PE<=polyethylene
are
●
Normally soiled laundry may be washed
without prewashing in order to save
detergent, water and time (the environment
is protected too!).
>PS<=polystyrene
>PP<=polypropylene
This means that they can be recycled by
disposing of them properly in appropriate
collection containers.
●
●
The machine works more economically if it is
fully loaded.
With adequate pre-treatment, stains and
limited soiling can be removed; the laundry
can then be washed at a lower temperature.
Measure out detergent according to the
water hardness, the degree of soiling and
the quantity of laundry being washed.
Old machine
Use authorised disposal sites for your old
appliance. Help to keep your country tidy!
●
The symbol
on the product or on its
packaging indicates that this product may not
be treated as household waste. Instead it shall
be handed over to the applicable collection
point for the recycling of electrical and
electronic equipment. By ensuring this product
is disposed of correctly, you will help prevent
potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product. For more detailed
information about recycling of this product,
please contact your local city office, your
household waste disposal service or the shop
where you purchased the product.
27
Download from Www.SSoumbajencut taolsc.hcaonmge. AwlilthMouatnnuoatilcseSearch And Download.
132 952 260 - 00 - 212009
|